ABB REPL-01 Скачать руководство пользователя страница 23

Страница: 23 / 87

Quick start-up guide

Mapping objects required for controlling the drive

1. In the Project Explorer window, right-click the entry for the
REPL-01 module, and select

Open I/O Configuration

in the pop-

up menu.

2. In the I/O Configuration window, make the following settings:

• General - Module supervised:

off

Note:

Setting Module supervised to

causes the PLC to drop

into service mode if the communication with the module fails. This
may be desirable in production environment. However, in testing
the recommended setting is

off

• Channels - TransparentControlWord_I2005 -

Cyclic transmission:

Write

• TransparentReferenceSpeed_I2006 - Cyclic transmission:

Write

Note:

Use Transparent objects (I2004-I2008) when the module is

in Transparent mode and Profile objects (I6040 onwards) when
the module is in Profile mode.

• Channels - TransparentStatusWord_I2007 - Cyclic

transmission:

Read

• Channels - TransparentActualFeedback_I2008 - Cyclic

transmission:

Read

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

Содержание REPL-01
























































































Результаты поиска

Содержание REPL-01

Отзывы:

Похожие инструкции для REPL-01

Бренды по названию

Популярные бренды

ABB REPL-01, Руководство пользователя

Результаты поиска

Содержание REPL-01

Отзывы:

Похожие инструкции для REPL-01

Бренды по названию

Популярные бренды