ABB PSE 105 Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 104

ABB PSE 105 Скачать руководство пользователя страница 60

Softstarters Type PSE18...PSE370 Installation and commissioning manual 1SFC132057M0201

60 Chapter 7

7.5 Functions

This chapter describes all settings and functions possible in the PSE Softstarter,

as well as the easiest way of finding them. Respective

default values, setting

ranges and parameter strings shown in the display are also stated.

7.5.1 Rated Current Ie of motor

This parameter allows for configuring of the current that the softstarter will be

exposed to. Since the motor must be connected In Line, set the rated motor cur-
rent, which can be found on the motor rating plate.

Display

Default value

Setting range

Description

Individual
(depending on size)

Individual
(depending on size)
See tables in
chapter 3.7.3 PSE
Softstarter types.
Setting range is 30-
100 percent of Ie

Rated motor current
Ie

Caution!

Connecting Softstarters PSE18...PSE370 Inside Delta will cause damage to

the equipment, and there is a risk of death or serious injury.

7.5.2 Start Ramp Time

The Start Ramp Time parameter allows for tuning of the time for the start ramp to
reach full voltage (Top of Ramp, TOR).

This parameter is controlling both voltage controlled and torque controlled start
ramps.

When a start signal is given the PSE Softstarter performs a start ramp by control-
ling the output voltage to the motor so that the voltage is increased linearly from
the initial voltage level to full voltage. Since the torque depends on both the volt-
age and the current, the torque curve does not always follow the voltage curve.
This has the effect that the torque curve will not increase linearly. If parameter
Torque Control Start is set to OFF, a voltage ramp will be performed during the

start ramp. The voltage and RPM of the motor will follow the graph in figure 7.5. If

a torque curve with linear increase is preferred, choose Torque Control during start
ramp described in chapter 7.5.6.

Display

Default value

Setting range

Description

10 s

0-30 s

Setting time for volt-
age controlled, and
torque controlled,
start ramps

The time set in Start Ramp Time is also the setting for the time in Torque Control
Start, if this parameter is enabled.

Figure 7.3: Rated Current parameter displayed

Figure 7.4: Start Ramp Time parameter

displayed

1SFC132160F0001

U

rpm

Figure 7.5: The function of Start Ramp Time

«
...
58
59
60
61
62
...
»

Содержание PSE 105









































































































Отзывы:

Нет отзывов