ABB PowerValue 11T G2 1 kVA B Скачать руководство пользователя страница 12

Страница: 12 / 28

POWE RVA LU E 11T G 2

1-3 K VA B/S

—
05 Output
connection
diagram of 3kVA S

3 2 1

UPS input connection

If the UPS is connected via the power cord, use a
proper socket (grounded and shockproof) and
pay attention to the capacity of the socket.
The UPS system has an input breaker on the
standard cabinet.

3 2 2

UPS output connection

The output sockets and types of the UPS are
shown below.

—

Table 5: UPS model output sockets

Model No

Output Socket -IEC(pcs)

PowerValue 11T G2 1 kVA B

4*C13

PowerValue 11T G2 1 kVA S

3*C13

PowerValue 11T G2 2 kVA B

4*C13

PowerValue 11T G2 2 kVA S

6*C13

PowerValue 11T G2 3 kVA B

4*C13+1*C19

PowerValue 11T G2 3 kVA S

3*C13+Terminal block

For PowerValue 11T G2 3kVA S model, connect the
output and ground wires to the terminal block
according to Figure 5 and Table 6 shown below.

—

Table 6: Connecting output and ground

wires to terminal block

Terminal
position

Wire function

Terminal
wire size
rating

Tightening
torque

Line Out

1.5mm

–

2.5mm

(14AWG-
12AWG)

0.5Nm

(4.4 Lb In)

Neutral Out

Output
Ground

3 2 3

External batteries connection

When connecting the external batteries modules
(EBM), it is recommended to use the EBM that
matches the corresponding UPS model.

—

Table 7: EBM and corresponding UPS model connections

UPS Model

EBM model

PowerValue 11T G2 1 kVA B

External battery 11T G2 1 kVA

PowerValue 11T G2 1 kVA S

External battery 11T G2 1 kVA

PowerValue 11T G2 2 kVA B

External battery 11T G2 2 kVA

PowerValue 11T G2 2 kVA S

External battery 11T G2 2 kVA

PowerValue 11T G2 3 kVA B

External battery 11T G2 3 kVA

PowerValue 11T G2 3 kVA S

External battery 11T G2 3 kVA

WARNING

CONNECTING THE WRONG EBM WILL
CAUSE ABNORMALITY OR PERMANENT
DAMAGE.

A STANDARD TYPE BATTERY CONNECTOR
ON THE REAR PANEL IS USED FOR
CONNECTING THE BATTERY PACK.

DANGER

IN CASE OF INSTALLING A CUSTOMIZED
EXTERNAL BATTERY PACKAGE, IT IS VERY
IMPORTANT TO FOLLOW THE NEXT STEPS
TO AVOID THE RISK OF ELECTRICAL SHOCK.

1. Prepare the battery cable and connector able

to withstand the needed current.

2. Install a proper DC breaker between the UPS

and the external batteries.

3. If there is a battery breaker, turn it off first.

Then connect the battery cable to the EBM
connector on the rear of the UPS.

4. Connect the input power cord of the UPS to

mains power supply. The battery will start to
charge.

—

3 2 Connection

—
05

Содержание PowerValue 11T G2 1 kVA B




























Результаты поиска

Содержание PowerValue 11T G2 1 kVA B

Отзывы:

Похожие инструкции для PowerValue 11T G2 1 kVA B

Бренды по названию

Популярные бренды

ABB PowerValue 11T G2 1 kVA B, Руководство пользователя

Результаты поиска

Содержание PowerValue 11T G2 1 kVA B

Отзывы:

Похожие инструкции для PowerValue 11T G2 1 kVA B

Бренды по названию

Популярные бренды