manualshive.com logo in svg

ABB MotiFlex e180, Инструкция по применению

Поделиться
Скачать
ABB MotiFlex e180 Скачать руководство пользователя страница 42

42   Reference

Introduction

The EtherCAT protocol provides deterministic communication over a standard 
100 Mbit/s (100Base-TX) Fast Ethernet (IEEE 802.3u) connection. This makes it 
suitable for the transmission of control and feedback signals between the 
MotiFlex e180 and other EtherCAT enabled controllers. EtherCAT's 'CAN application 
layer over EtherCAT' (CoE) capability allows Mint to implement a drive protocol based 
on the CANopen DS 402 Device Profile for Drives and Motion Control.

The MotiFlex e180 incorporates a built-in multi-port EtherCAT slave controller, 
providing two ports for connection to other equipment. This allows nodes to be 
connected in many configurations such as a ring, star, or tree, with EtherCAT's self-
terminating technology automatically detecting breaks or an intended end of line. 
Standard Ethernet switches can be used in EtherCAT networks.

The MotiFlex e180 has passed the formal EtherCAT conformance test, which is 
performed using a network with a wide range of EtherCAT devices. It has also been 
tested with many different types of master device to ensure interoperability, including:

• ABB AC500 PLC with EtherCAT master (CM579-ETHCAT).
• acontis technologies EC-master stack and EC-Win
• Beckhoff CX8000/9000 Embedded PC
• Beckhoff TwinCAT (soft master NC PTP)
• esd EtherCAT master
• Hilscher cifX PC card
• Konig KPA Master/Studio (v1.4.8.15)
• 3S CoDeSys v3 (Soft-PLC)

Supported mailbox protocols

• CoE
• FoE
• EoE

Synchronisation

The drive supports two synchronisation modes.

DC (distributed clock) synchronisation

DC synchronisation is preferred for all applications with multiple drives and 
coordinated motion, since it provides the most precise synchronisation. The DC 
mode compensates for the Ethernet hop delay. This means that independent of the 
size of the network all nodes apply the demand values at the same time.

Содержание MotiFlex e180









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды