ABB JDF300, Инструкция по эксплуатации, Страница: 20 / 52

20
J DF 3 0 0 |
FI EL D I N D I C ATO R | O I/J D F 3 0 0 - EN R E V. B
. . .RESOURCE Block Mapping
Idx Parameter Description / Range / Selections / Notes
21 MIN_CYCLE_T Time duration of the shortest cycle interval of which the resource is capable.
22 MEMORY_SIZE Available configuration memory in the empty resource. To be checked before attempting a download
23 NV_CYCLE_TIME
Min. time interval for writing copies of NV parameters to non-volatile memory. Zero means it will be never
automatically copied.
24 FREE_SPACE Percent of memory available for further configuration. Zero in a preconfigured device
25 FREE_TIME Percent of the block processing time that is free to process additional blocks.
26 SHED_RCAS
Time duration at which to give up on computer writes to function block Rcas locations. Shed from Rcas shall never
happen when Shed_Rcas = 0
27 SHED_ROUT
Time duration at which to give up on computer writes to function block Rout locations. Shed from Rout shall never
happen when Shed_Rout = 0
28 FAULT_STATE Fault State
29 SET_FSTATE Set Fault State
30 CLR_FSTATE Clear Fault State
31 MAX_NOTIFY Maximum number of unconfirmed alert notify messages possible
32 LIM_NOTIFY Maximum number of unconfirmed alert notify messages allowed
33 CONFIRM_TIME The min time between retries of alert report. Retries shall not happen when Confirm_Time = 0
34 WRITE_LOCK
1 Unlocked (default)
2 Locked
If set, no writes are allowed except to clear Write_Lock.
Block inputs will continue to be updated
35 UPDATE_EVT This alert is generated by any change to the static data
36 BLOCK_ALM
The block alarm is used for all configuration, hardware, connection failure or system problems in the block. The cause
of the alert is entered in the subcode field. The first alert to become active will set the Active Status in the status
parameter. As soon as the Unreported status is cleared by the alert reporting task, another block alert may be
reported without clearing the Active Status, if the subcode has changed
37 ALARM_SUM The alert status associated to the function block
38 ACK_OPTION
0 Auto Ack Disabled (default)
Selection of whether alarms associated the function block
will be automatically acknowledged
1 Auto Ack Enabled
39 WRITE_PRI Priority of the alarm generated by clearing the write_lock
40 WRITE_ALM This alert is generated if the write_lock parameter is cleared
41 ITK_VER 6
42 CB_SW_REV “XX.YY.ZZ” (08.01.01)
43 CB_HW_REV “XX.YY.ZZ” (01.00.00)
44 CAPABILITY_LEV Not Supported
45 COMPATIBILITY_REV 0x01
46 FD_VER Indicates value of major version of instrument diagnostics specifications (FF-912).
47 FD_FAIL_ACTIVE Active error conditions of Failure category
According to the NAMUR NE107 Categories.
Bit x = 0 – Error Clear
Bit x = 1 – Error Active
It is a bit-string so that multiple errors of the list below
may be shown.
48 FD_OFFSPEC_ACTIVE Active error conditions of Out of Specification category
49 FD_MAINT_ACTIVE Active error conditions of Maintenance category
50 FD_CHECK_ACTIVE Active error conditions of Check Function category.
51 FD_FAIL_MAP Errors Mapped as Failure Default mapping: Bit 4 Electronic memory fail
52 FD_OFFSPEC_MAP Errors Mapped as Out of Spec Default mapping: none
53 FD_MAINT_MAP Errors Mapped as Maintenance: Default mapping:
Bit 2 MAO not Scheduled
Bit 3 MAO inputs all disabled
Bit 5 NV memory burn error
54 FD_CHECK_MAP Errors Mapped as Function Check
Default mapping:
Bit 0 Function Check
Bit 1
MAO in OOS
55 FD_FAIL_MASK Fail error to be masked
Default no error masked
56 FD_OFFSPEC_MASK Out of Spec errors to be masked
57 FD_MAINT_MASK Maintenance errors to be masked
58 FD_CHECK_MASK Function Check errors to be masked