ABB HT608782 Скачать руководство пользователя

Страница: 4 / 148

Operation Manual / A170-M.. - A175-M..

Table of contents

HZTL4033_EN

Rev.I

November 2021

Stopping the engine................................................................................................... 52

Periodic maintenance.......................................................................................... 53

7.1

Foreword to maintenance......................................................................................... 53

7.2

Cleaning the filter silencer ........................................................................................ 54

7.3

Cleaning the slotted diffuser.................................................................................... 56

7.4

Cleaning the compressor during operation ........................................................... 57

7.5

Cleaning turbine and nozzle ring ............................................................................. 63

Troubleshooting................................................................................................... 69

8.1

Malfunctions when starting...................................................................................... 69

8.2

Malfunctions during operation ................................................................................ 70

8.3

Surging of the turbocharger...................................................................................... 72

8.4

Malfunctions when stopping..................................................................................... 73

8.5

Speed measurement system .................................................................................... 74

Disassembly and assembly................................................................................. 75

9.1

Introduction .................................................................................................................. 75

9.2

Weight of assemblies.................................................................................................. 77

9.3

Removing the air inlets .............................................................................................. 78

9.4

Axial clearance A prior to disassembly ................................................................... 80

9.5

Removing the compressor casing ............................................................................ 81

9.6

Removing the cartridge group ................................................................................. 85

9.7

Removing the nozzle ring .......................................................................................... 88

9.8

Installing the nozzle ring ........................................................................................... 93

9.9

Installing the cartridge group .................................................................................. 98

9.10

Fitting the spinner nose cone ................................................................................. 101

9.11

Installing the compressor casing .......................................................................... 103

9.12

Axial clearance A after assembly............................................................................ 107

9.13

Installing the air inlets ............................................................................................. 108

9.14

Removing and installing turbine-end nozzle ring................................................ 111

9.15

Table of tightening torques..................................................................................... 115

Taking a turbocharger out of operation......................................................... 118

10.1

Possible emergency repairs..................................................................................... 118

10.2

Locking the rotor ....................................................................................................... 119

10.3

Fitting the cover plate............................................................................................... 122

10.4

Blanking off the inlets and outlets ......................................................................... 124

10.5

Engines with bypass around the turbocharger ................................................... 124

Mothballing the turbocharger.......................................................................... 125

11.1

Taking the engine out of operation for up to 12 months .................................. 125

11.2

Taking the engine out of operation for more than 12 months ......................... 126

Material and Disposal........................................................................................ 127

12.1

REACH and RoHS Compliance Declaration For Products .................................. 127

12.2

Disposing of turbocharger components .............................................................. 128

Содержание HT608782



















































































































































Результаты поиска

Содержание HT608782

Отзывы:

Похожие инструкции для HT608782

Бренды по названию

Популярные бренды

ABB HT608782, Руководство по эксплуатации

Результаты поиска

Содержание HT608782

Отзывы:

Похожие инструкции для HT608782

Бренды по названию

Популярные бренды