ABB HT608782 Скачать руководство пользователя | Manualshive

Страница: 90 / 148

background image

Operation Manual / A170-M.. - A175-M..

9 Disassembly and assembly / 9.7 Removing the nozzle ring

© Copyright 2021 ABB. All rights reserved.

HZTL4033_EN

Rev.I

November 2021

9.7

Removing the nozzle ring

Removing the turbine diffuser

CAUTION

Risk of mixing up the press-off screws

In size A170-M, the press-off screw (90915) for pressing off the turbine dif-
fuser with thread size M18x1.0 can easily be mixed up with the press-off
screw (90901) with thread size M18x1.5. If the press-off screws are mixed up,
the thread of the turbine diffuser can be damaged.

u

Always use the appropriate press-off screws.

Fig. 44: Removing turbine diffuser 1

1. Remove screws (61069).

2. Using press-off screws (90915), press off turbine diffuser.

3. Fit guide plates (90328) with nuts (61037).

4. Screw in guide stud (90802).

Page

88

/

146

«
...
88
89
90
91
92
...
»

Содержание HT608782





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для HT608782

Бренд: GALLERY Страницы: 18

Бренд: NARGESA Страницы: 33

Бренд: Rain-Flo Irrigation Страницы: 20

Attest Auto-reader 390

Бренд: 3M Страницы: 2

Бренд: 3M Страницы: 2

Бренд: 3M Страницы: 2

Dynapro ET 355 Monitor HL

Бренд: 3M Страницы: 23

PELTOR WS LiteCom Plus

Бренд: 3M Страницы: 7

Steri-Vac GS Series

Бренд: 3M Страницы: 52

Бренд: E-Z DRILL Страницы: 12

Бренд: e-survey Страницы: 54

Бренд: E-Pill Страницы: 8

XL-7 Command Station

Бренд: E-Mu Страницы: 22

Бренд: p-light Страницы: 28

Бренд: Waterpik Страницы: 2

Бренд: Hedson Страницы: 32

Бренд: JLG Страницы: 165

Бренд: Labconco Страницы: 174

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды