ABB HT568698 Скачать руководство пользователя

Страница: 57 / 124

Operation Manual / TPL65VA32/33

Maintenance

Cleaning the filter silencer

5.2

Page 55

ber

2016

L2464_

ion

Removing and cleaning filter silencer



Remove filter strip (81265).



Rinse filter strip (81265) using water with detergent additive or, if very

dirty, soak it and squeeze out carefully. Rinse it in cold water. Avoid

rough treatment (not a jet of water).

NOTICE

How dirty the filter strip (81265) is, depends on how clean the drawn-in

air is. Clean filter strip every 500 hours of service or more frequently if

necessary.



Unscrew and remove lock nuts (81273).



Unscrew and remove screws (81272) for connecting rods (81269).



Remove connecting rods (81269).



Carefully remove cover grids (81266).



Pull out insert units (E), bend open sheet-metal coverings (81137) and

then remove absorption segments (81136).



Clean the absorption segments (81136).

During cleaning, ensure that the absorption segments (81136) are only

cleaned with a mild jet of compressed air, soft brush or a damp cloth.

Otherwise there is a risk of damage or deformation.

NOTICE

Replace heavily contaminated or damaged parts with original parts from

ABB Turbo Systems.

If provided

Содержание HT568698





























































































































Результаты поиска

Содержание HT568698

Отзывы:

Похожие инструкции для HT568698

Бренды по названию

Популярные бренды

ABB HT568698, Руководство по эксплуатации

Результаты поиска

Содержание HT568698

Отзывы:

Похожие инструкции для HT568698

Бренды по названию

Популярные бренды