ABB HT568698 Скачать руководство пользователя

Страница: 38 / 124

Operation Manual / TPL65VA32/33

Commissioning

Inspection work

3.2

Page 36

ber

2016

L2464_

ion

Inspection work

3.2

Inspection work includes preventive visual controls plus monitoring and

measuring work before and during commissioning. Inspections help detect

changes to the turbocharger. Machine damage can be avoided.

Inspection before commissioning



Check for correct functioning.



Inspect for damage.



Check oil filter for cleanliness before commissioning.

CAUTION

It is urgently recommended that the entire lubricating system be flushed

thoroughly with warm oil using a bypass pipe before starting up the first

time (commissioning) and after all service work on the lubricating sys-

tem.

It is urgently recommended that a running-in filter is used when running

in the engine and after all service work on the lubricating system.



Check the oil pressure in the oil supply lines.



Check that variable turbine geometry module can be adjusted.

TPL65: Version with compressor wheel cooling system



Check whether compressor wheel cooling system is fitted to bearing

casing.

CAUTION

Failure of compressor wheel cooling system
The service life of the compressor wheel will be impaired if the break-

down of the compressor wheel cooling system lasts long.



Ensure supply of cooling air.

3.2

3.2.1

Monitoring equipment

Air filter mat

Lubricating system

TPL..VA

Содержание HT568698





























































































































Результаты поиска

Содержание HT568698

Отзывы:

Похожие инструкции для HT568698

Бренды по названию

Популярные бренды

ABB HT568698, Руководство по эксплуатации

Результаты поиска

Содержание HT568698

Отзывы:

Похожие инструкции для HT568698

Бренды по названию

Популярные бренды