ABB HT564844 Скачать руководство пользователя страница 64

Страница: 64 / 128

Operation Manual / TPL67-C.. - TPL71-C..

Maintenance

Cleaning turbine blades and nozzle ring

in operation

5.4

Page 62

Apr

il 2016

L2488_

ion

When cleaning the turbine components during operation, use wet clean-

ing. This cleaning method has been tested and approved by ABB Turbo

Systems.

Prerequisites for wet cleaning are that the engine builder approves the

process and his instructions are followed.

During wet cleaning using droplets of water, the water does not act as a

solvent. Instead, the deposit is removed by the mechanical impact of the

drops.

CAUTION

Corrosion and deposits when cleaning
Damage and impairment of turbocharger parts due to salt water and

cooling water additives



Don't use salt water for cleaning, but only clean fresh water.

Components at the turbine end are not cleaned until the engine has been

started or the engine load reduced. The exhaust gas temperature must

not exceed the value specified in the respective cleaning instructions (see

section Prerequisites

[➙

]

CAUTION

Exhaust gas temperature, stabilising and drying time
Drastically reduced lifetime of component due to excessive inlet tem-

perature and varying temperature stresses in the component.



Always adhere to the respective cleaning instructions.

In the case of V-engines with several turbochargers on each engine, we

recommend parallel cleaning of both turbochargers. This cleaning process

is faster and the risk of turbocharger surging is reduced. We recommend

finding the most suitable method by performing trials.

Cleaning method

Principle of wet cleaning

V-engines

Содержание HT564844
































































































































Результаты поиска

Содержание HT564844

Отзывы:

Похожие инструкции для HT564844

Бренды по названию

Популярные бренды

ABB HT564844, Руководство по эксплуатации

Результаты поиска

Содержание HT564844

Отзывы:

Похожие инструкции для HT564844

Бренды по названию

Популярные бренды