ABB HT564844 Скачать руководство пользователя страница 93

Страница: 93 / 128

Operation Manual / TPL67-C.. - TPL71-C..

Disassembly and assembly

Dismantling and installing the turbine

diffuser and nozzle ring

8.6

Page 91

Apr

il 2016

L2488_

ion



Replace two screws (61056) in the gas outlet casing with two guide

studs (90320) in the upper section of the turbine diffuser (63000).



Fit clamps (90921) over guide studs (90320) and studs (61036).



To secure the work, screw nuts (61037) onto start of stud threads

(61036).



Remove the remaining screws (61056) and Verbus Ripp® washers

(61057).



Press the turbine diffuser (63000) free using the press-off screws

(90901) and pull it out it until the clamp (90921) is touching the nut

(61037).



Loop the lifting gear around the turbine diffuser (63000) and secure it

to a crane.



Remove the nuts (61037) and clamps (90921) from the stud.



Withdraw the turbine diffuser all the way and remove it.



Remove guide stud (90320).

Removing the turbine

diffuser

Содержание HT564844
































































































































Результаты поиска

Содержание HT564844

Отзывы:

Похожие инструкции для HT564844

Бренды по названию

Популярные бренды

ABB HT564844, Руководство по эксплуатации

Результаты поиска

Содержание HT564844

Отзывы:

Похожие инструкции для HT564844

Бренды по названию

Популярные бренды