ABB FCAN-01 Скачать руководство пользователя

Страница: 90 / 176

90 Communication profiles



Modes of operation

The operation mode defines the behavior of the drive. CiA 402

defines following operation modes:

•

Homing mode

•

Profile position mode

•

Interpolated position mode

•

Profile velocity mode

•

Profile torque mode

•

Velocity mode

The FCAN-01 CANopen adapter module supports minimal

implementation of the operation modes. Operation mode support is

drive-specific (see the figure at the beginning of this chapter). The

interpolated position mode is not supported.
In this chapter scalings of the reference and actual values are

described for each operation mode. Operation-mode-specific

objects are defined in section

CANopen Object Dictionary

on page

131

In ACSM1 drives, the mode of operation is automatically selected

according to the control mode configured with parameter

34.03

EXT1 CTRL MODE

34.04 EXT1 CTRL MODE2

34.05 EXT2

CTRL MODE1

(depending on the current control location). The

correct reference scaling must be selected with parameter

50.04

FBA REF1 MODESEL

If the value of parameter

50.04 FBA REF1 MODESEL

and

50.05

FBA REF2 MODESEL

of ACSM1 is (5) AUTO, it is possible to set

the mode of operation with object 6060h. For more information,

see section

Standardized device profile area (6000...9FFF)

page

146



Homing mode

Homing mode describes various methods of finding a home

position, or zero point. Either limit switches at the ends of travel or

a home switch in mid travel are used. Most of the methods also

use the index (zero) pulse from an encoder. For more information

on the homing mode and descriptions of the various homing

methods, see the drive manual.

Содержание FCAN-01

















































































































































































Результаты поиска

Содержание FCAN-01

Отзывы:

Похожие инструкции для FCAN-01

Бренды по названию

Популярные бренды

ABB FCAN-01, Руководство пользователя

Результаты поиска

Содержание FCAN-01

Отзывы:

Похожие инструкции для FCAN-01

Бренды по названию

Популярные бренды