ABB EasyLine Series Скачать руководство пользователя страница 127

Страница: 127 / 136

Status

Messages,

Troubleshooting

127

No. Status Message

Reaction/Troubleshooting

359 A S a The intensity measured at the detector

exceeds or falls below alarm value 2.

Notify Service.

360 A S a The filter wheel could not be initialized.

If the status message is active for longer
than 5 minutes, the filter wheel is blocked.

362 A S a The calibration filter wheel cannot be

initialized.

If the status message is active for longer
than 5 minutes, the calibration filter wheel
is blocked.

378 A S aL The chopper wheel is blocked.

Visual check. Notify Service.

379 A S aL Chopper wheel speed not OK.

Notify Service.

380  A  S  aL  IR source element or electronics defective. Notify Service.
381  A  S  aL  High voltage in the preamplifier defective.  Notify Service.
382  A  S  aL  Measured value is influenced by shocks.

390 A S aQ Failure of the power supply inside the

module. Notify Service.

Notify Service.

397 A S a The sensor of the temperature regulator is

defective.

Notify Service

398 A S aL No new measured values from the

analog/digital converter.

Notify Service.

399 A S a The measured value exceeds the value

range of the analog/digital converter.

Check the sample gas concentration.
Check connectors in the gas analyzer.
Notify Service.

400 A S a A calculation error occurred during

calculation of the measured value.

Switch the power supply off and on. Notify
Service.

401 W a The flow is above or below the upper or

lower alarm value 1.

Check sample gas path. Notify Service.

402 A S a The flow is above or below the upper or

lower alarm value 2.

Check sample gas path. Notify Service.

403 A S a The flow controller output variable is

beyond the valid range.

Notify Service.

404 A S a The temperature is above or below the

upper or lower alarm value 2.

Notify Service.

411 F S a The analyzer is in standby mode.

Reactivation in the Menu: Operation /
Pump/Standby / Fidas Standby.. Fidas
Restart.

Restart of the Fidas24.

412 F S a Ignition failed. The analyzer must be

manually reactivated. Reactivation in the
Menu: Operation / Pump/Standby / Fidas
Standby.. Fidas Restart.

Check process gases.
Restart of the Fidas24.

413 A S aL Auxiliary voltage failure in the analyzer

hardware.

Notify Service.

414 F S a The controlled variable of this controller is

below the permissible range (< 20%).

415 F S a The controlled variable of this controller is

above the permissible range (< 90%)

Check the process gases and connection
lines. If required, restart of the Fidas24.
Notify Service.

500 iQ An internal calibration error has occurred. Repeat the calibration. Check the

configuration with TCT. Notify Service.

501 iQ The requested functional capability is not

available in the instrument.

Check the configuration with TCT.

Содержание EasyLine Series









































































































































Результаты поиска

Содержание EasyLine Series

Отзывы:

Бренды по названию

Популярные бренды

ABB EasyLine Series, Инструкция по установке, запуску и эксплуатации

Результаты поиска

Содержание EasyLine Series

Отзывы:

Бренды по названию

Популярные бренды