ABB DPA UPScale ST40 Скачать руководство пользователя страница 7

Страница: 7 / 129

Modifications reserved

Page 7/79

WARNING!

HIGH FAULT CURRENTS (LEAKAGE CURRENTS):

BEFORE CONNECTING THE MAINS, YOU MUST ENSURE THAT THERE IS
A PROPER EARTH CONNECTION!

WARNING!

THE USER MUST DISPLAY A WARNING SHIELD ON ALL PRIMARY UPS
CIRCUIT BREAKERS. THE SERVICE PERSONNEL HAS TO BE INFORMED

ABOUT DANGEROUS VOLTAGES. THE WARNING PANELS MUST CONTAIN
THE FOLLOWING TEXT: “ BEFORE STARTING WITH MAINTENANCE WORK

ON THE CIRCUIT BREAKERS, MAKE SURE THE UPS IS ISOLATED.”

1.2

Safety symbols and warnings

PROTECTIVE GROUNDING TERMINAL

A terminal which must be connected to earth ground prior to making any

other connection to the equipment.

A terminal to which or from which a direct current or voltage may be

applied or supplied.

This symbol indicates the word “phase”.

The principal power switch is in the “ON” position

OFF

The principal power switch is in the “OFF” position.

CAUTION: REFER TO MANUAL

Refer to the Operator’s manual for more information

DANGER: RISK OF ELECTRIC SHOCK

There is a risk of electric shock present, and you should observe
associated warnings. The UPS contains high voltages.

Содержание DPA UPScale ST40




























































































































Результаты поиска

Содержание DPA UPScale ST40

Отзывы:

Бренды по названию

Популярные бренды

ABB DPA UPScale ST40, Руководство пользователя

Результаты поиска

Содержание DPA UPScale ST40

Отзывы:

Бренды по названию

Популярные бренды