ABB DPA UPScale ST40 Скачать руководство пользователя страница 35

Страница: 35 / 129

Modifications reserved

Page 35/79

NOTE: For UPS-Systems DPA UPScale M-10kW, M-20kW it is permissible to use 40-50 (only

even numbers) of 12V-battery blocks.

For UPS-System UPScale M-20kW use only 48-50 (only even numbers) of 12V-battery blocks.

NOTE: Set-up the correct number of battery blocks on control panel (menu: service-set-up).

Frame: DPA UPScale ST S2 80 or ST 120 frames with Modules M 10 or M 20

CBAT UPScale-120

CBAT UPScale-200

5x28Ah

Battery Cabinet 120

5x28Ah 5x28Ah

5x28Ah

(3x40)x28Ah

Battery Cabinet 200

5x28Ah

(5x40)x28Ah

Fig 5.6.1-1: External battery configuration

CBAT UPScale-120

Fig 5.6.1-2: External battery configuration

CBAT UPScale-200

CBAT UPSCALE-120

Dimensions (WxHxD)

730x1975x800

1200x1975x800

Weight with trays and w/o batteries

290

410

For detailed information on, and layout of, the battery cabinets, please refer to the “external battery

cabinets” chapter of the technical data sheet.

Examples:

On drawing “CBAT UPScale-120” (3x40)x 28 Ah battery blocks are fitted. The lower batch of 40x 24

Ah belong to the UPS 1, the middle batch of 40x 24 Ah belong to the UPS 2 and the top batch of 40x

24 Ah belong to the UPS 3.

On drawing “CBAT UPScale-200” (5x40)x 28 Ah battery blocks are fitted in the battery cabinet and

each UPS module is provided with 40x 28 Ah.

Depending on the configuration requested, the batteries may be connected separately for each

module or paralleled into one common battery for five UPS modules.

Содержание DPA UPScale ST40




























































































































Результаты поиска

Содержание DPA UPScale ST40

Отзывы:

Бренды по названию

Популярные бренды

ABB DPA UPScale ST40, Руководство пользователя

Результаты поиска

Содержание DPA UPScale ST40

Отзывы:

Бренды по названию

Популярные бренды