ABB A145-H66 страница 140 Скачать руководство пользователя

Страница: 140 / 142

Operation Manual / 4 Product description / A130-M.. - A145-M..

Figures

HZTL4031_EN

Revision F

August 2017

Figures

Fig. 1: Layout and function of the turbocharger ...... 4

Fig. 2: Compressor wheel cooling ................................ 5

Fig. 3: Warning plate locations .................................... 6

Fig. 4: Locations of the rating plates .......................... 7

Fig. 5: Suspension of complete turbocharger unit.. 8

Fig. 6: Removing the turbocharger............................. 9

Fig. 7: Loosening the clamping nut............................ 11

Fig. 8: Turbocharger centre of gravity ...................... 12

Fig. 9: Inserting gaskets into the bracket ................ 13

Fig. 10: Inserting the threaded rods .......................... 14

Fig. 11: Requirements for threaded rods .................. 14

Fig. 12: Placing the turbocharger on the bracket ... 15

Fig. 13: Preparing the clamping nut for the tighten-
ing procedure ................................................................ 17

Fig. 14: Tightening pressure screws.......................... 18

Fig. 15: Connecting the compressor cooling air in-
take .................................................................................. 19

Fig. 16: Attaching the support .................................... 19

Fig. 17: Oil orifice ........................................................... 21

Fig. 18: Layout and overview of speed measurement
system ............................................................................ 28

Fig. 19: Replacing the speed sensor ......................... 30

Fig. 20: Noise insulation, bellows............................... 32

Fig. 21: Replacing the protective grid....................... 35

Fig. 22: Carrying out wet cleaning of compressor. 44

Fig. 23: Carrying out wet cleaning of turbines ....... 48

Fig. 24: Cleaning the filter silencer ........................... 50

Fig. 25: Compressor-end, non-rotating parts ........ 52

Fig. 26: Turbine end, non-rotating parts ................. 53

Fig. 27: Soaking the turbine end................................ 56

Fig. 28: Weights of assemblies .................................. 70

Fig. 29: Removing air inlets ......................................... 71

Fig. 30: Removing the insulation................................ 72

Fig. 31: Removing the gas outlet casing ................... 73

Fig. 32: Dismantling the gas outlet flange................ 75

Fig. 33: Removing the gas outlet flange.................... 76

Fig. 34: Removing the compressor casing ............... 77

Fig. 35: Dismantling the wall insert............................ 78

Fig. 36: Press off the casing ........................................ 79

Fig. 37: Removing insulation sheets .......................... 80

Fig. 38: Oil orifice ........................................................... 80

Fig. 39: Removing cartridge group 1.......................... 81

Fig. 40: Removing cartridge group 2 ......................... 81

Fig. 41: Removing the nozzle ring ............................... 82

Fig. 42: Installing the cartridge group on the service
support ............................................................................ 83

Fig. 43: Measuring clearance A and B ........................ 84

Fig. 44: Nozzle ring compression PD ......................... 85

Fig. 45: Installing the nozzle ring................................ 86

Fig. 46: Lifting the cartridge group and rotating it
by 90° ............................................................................... 87

Fig. 47: Installing the cartridge group ....................... 88

Fig. 48: Turbine casing insulation / Burst protection.
89

Fig. 49: Installing the compressor casing................. 91

Fig. 50: Measuring clearances N and R...................... 92

Fig. 51: Installing the air inlets .................................... 93

Fig. 52: Installing the gas outlet flange ..................... 94

Fig. 53: Fitting the insulation ...................................... 95

Fig. 54: Installing the gas outlet casing .................... 96

Fig. 55: Fitting the insulation ...................................... 97

Fig. 56: Tightening torques ........................................ 98

Fig. 57: Tightening torques for insulation ................ 99

Fig. 58: Fitting the cover plate .................................. 102

Fig. 59: Cover plate drawing...................................... 103

Fig. 60: Overview of part numbers........................... 108

Page

110

111

Page

110

111

Содержание A145-H66















































































































































Результаты поиска

Содержание A145-H66

Отзывы:

Похожие инструкции для A145-H66

Бренды по названию

Популярные бренды

ABB A145-H66, Оригинальное руководство по эксплуатации

Результаты поиска

Содержание A145-H66

Отзывы:

Похожие инструкции для A145-H66

Бренды по названию

Популярные бренды