ABB A145-H66 страница 27 Скачать руководство пользователя | Manualshive

Страница: 27 / 142

background image

Operation Manual / 2 Safety / A130 - A155

1 Safety / 1.14 Safe maintenance

© Copyright 2017 ABB. All rights reserved.

HZTL4022_EN

Revision E

May 2017

Mechanical hazards when working on the turbocharger

WARNING

Physical hazards due to rotating parts

The rotor can rotate due to the stack draught alone. Contact with rotating
parts can cause severe injury.

u

Secure rotor against turning.

WARNING

Mechanical hazards

Severe injuries to personnel or fatal accidents can be caused by mechanical
influences as a consequence of hazardous and inadequate operational pro-
cedures.

u

Observe the general rules for occupational safety and prevention of acci-
dents.

u

Ensure workplace safety.

u

Only perform operations that are described in this chapter.

u

Only perform operations for which you have previously received instruc-
tion or training.

Hazards due to operating materials and supplies

Operating materials and supplies are substances required for the operation of the tur-
bocharger or for the performance of maintenance work. Oils, greases, coolants, detergents
and solvents, acids and similar substances can be classified as hazardous substances.

WARNING

Handling operating materials and supplies

Swallowing or inhaling vapours of operating materials and supplies or con-
tact with them may be harmful to health.

u

Do not breathe in these substances and avoid contact with the skin.

u

Ensure proper ventilation.

u

Observe the information in the material safety data sheet for the operat-
ing materials and supplies.

u

Wear personal protective equipment (PPE) according to the material
safety data sheet.

u

Comply with local legislation.

Wear safety goggles.

Wear safety gloves to protect against chemical hazards.

Wear a respiratory mask to protect against gases.

Page

17

/

18

«
...
25
26
27
28
29
...
»

Содержание A145-H66















































































































































Отзывы:

Нет отзывов

Похожие инструкции для A145-H66

Бренд: Nemco Страницы: 13

Бренд: Ecco Страницы: 12

Бренд: UMF Medical Страницы: 12

Бренд: Raytheon Страницы: 69

Бренд: Galaxy Audio Страницы: 24

WJHD309A - DIGITAL DISK RECORDER

Бренд: Panasonic Страницы: 79

Бренд: G-Lab Страницы: 16

Бренд: G&G Страницы: 2

Synthesis SDEC-3000

Бренд: JBL Страницы: 24

Бренд: Xilica Audio Design Страницы: 30

FlexDraper FD2 Series

Бренд: MacDon Страницы: 2

OXYGEN PRO MINI

Бренд: M-Audio Страницы: 56

Бренд: Abus Страницы: 12

Бренд: Fagor Страницы: 12

Бренд: Baltic Страницы: 68

Бренд: H&S Страницы: 76

Бренд: Feniex Страницы: 5

TR 2B INC INT NC

Бренд: OMGA Страницы: 76

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды