background image

 

SAFETY INSTRUCTIONS 

 

REQUIREMENTS FOR SAFE OPERATION 

1.  Never allow unauthorized individuals or children to operate the unit at any time. 
2.  Abatement  Technologies  urges  anyone  operating  HEPA-AIRE®  scrubber  units  to  wear  the  proper 

personal protective equipment and follow safe work practices in accordance with federal, state, local, 
provincial and employer regulations. 

3.  Check the condition of power cord(s) before using them. Damaged cords can cause fatal electric shock 

and/or motorized impeller failure. 

4.  Power cord(s) should never be exposed to water, heat, and/or sharp or abrasive objects.  In addition, 

they should never be kinked or crushed.  Avoid tightly wrapping the cords to prevent kinking of the internal 
wires. Always replace damaged power cords immediately. 

5.  Never pull the unit by the power cord. 
6.  Avoid running over power cords with utility equipment and vehicles. 

 

 

If  the  equipment  is  used  in  a  manner  not  specified  by  the  manufacturer,  the  protection  provided  by  the 

equipment may be impaired. 

 

IMPORTANT SAFETY INSTRUCTIONS 

a.  Do not operate any unit with a damaged cord or plug.  Discard unit or return it to an authorized service 

facility for examination and/or repair. 

b.  Do not run cord under carpeting.  Do not cover cord with throw rugs, runners, or similar coverings. Do 

not route cord under furniture or appliances.  Arrange cord away from traffic area and where it will not be 
tripped over. 

 

 

Caution: 

As with any piece of electrical equipment, always make sure that the unit is turned “OFF” prior to 

connecting the power cord to an electrical outlet or disconnecting it from an electrical outlet. Failure to do 
so will cause “arcing”, and could result in personal injury, fire hazards and/or damage to the unit. Do not 
disconnect the power cord from supply receptacle while the unit is operating.

 

 

 

Warning: 

To reduce risk of electrical shock, do not expose this unit to water or rain. Do not touch the electrical 

outlet or power cord(s) with wet hands or while standing on a wet or damp surface.

 

 

 

Warning: 

Risk of electrical shock! Can cause injury or death! Turn unit “OFF” and disconnect power cord 

from supply receptacle before replacing the HEPA filter and before cleaning or servicing the unit.

 

 

 

Warning: 

To reduce the risk of fire, electric shock, or injury to person observe the following:

 

Use this unit 

only  in  the  manner  intended  by  Abatement  Technologies.  If  you  have  questions,  contact  Abatement 
Technologies at +1 800-634-9091 (U.S.) or +1 905-871-4720 (Canada).

 

 

 

Warning: 

This unit is equipped with an automatic restart motorized impeller that will restart without warning 

after a temporary power interruption or recovery from a thermal overload (over-heating) condition.  Keep 
clear of the motorized impeller at all times to reduce the risk of injury.

 

 

 

Warning: 

To reduce risk of fire or electrical shock, do not use this unit with any solid-state speed control 

device.  Do not use in a cooking area. 

 

 

Warning: 

Do not position the unit so that it is difficult to operate the disconnecting device.  The disconnecting 

device is the power cord plug.

 

 

 

Caution: 

This unit is designed for indoor use only.

 

 

Содержание HEPA-AIRE PAS1200



















Отзывы: