manualshive.com logo in svg

AB Regin Corrigo E151-3, Руководство пользователя

Поделиться
Скачать
AB Regin Corrigo E151-3 Скачать руководство пользователя страница 84

 

84 

Chapter 17 

  Configuration 

Manual Corrigo Ventilation, revision R 

17.6 Extra sequence Y4 

"Extra sequence Y4" can be configured to one of the following alternatives: "Active", "Active with 
cooling recovery", "Active with enthalpy control" and "Active with both cooling recovery and 
enthalpy control". 

Mode Extra Seq- 
uence Y4 
 
Not active 

17.7 Extra sequence Y5 

"Extra sequence Y5" can be configured to “Active” or “Not active”. 

Mode Extra Seq- 
uence Y5 
 
Not active 

 

17.8 Heating coil 

Heating 
water 
 
 

The heater can be set to "Water", "Electric", "Water/Electric" or "Not used". 

For detailed description of heater alternatives, see section 5.1.2 Heater types. 

17.9 Exchanger 

Exchanger        
Rot. Exch 
                    
 

The heat exchanger unit can be set to one of the following alternatives:  

•

 

Plate exchanger 

•

 

Rotating exchanger 

•

 

Liquid connected exchanger 

•

 

Mixing dampers 

•

 

Not connected 

•

 

Damper limiting for minimum outdoor air percentage is settable 0…100%. 

In the submenu parameters for outdoor temperature control of exchanger can be set. 

Outd. temp control of 
exch: Off 
Outd. temp start: 10°C 
Diff. stop: 0.2°C 

For detailed description of exchanger alternatives, see section 5.1.3 Heat exchanger. 

Содержание Corrigo E151-3























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды