AAON SS1113 Скачать руководство пользователя страница 61

Страница: 61 / 62

Main Chiller Controller Technical Guide

APPENDIX B - BACnet

BACnet

Parameters

ANALOG VALUES

BACnet

Point Name

Object

BACnet

Description

Limit Range

Vestibule
Heating
Setpoint

AV:9

If the Vestibule Temperature drops below this setpoint
the heating mode will activate on the Fan Coil.

50-90

Vestibule Heat/
Cool Setpoint
Deadband

AV:10

The Vestibule temperature has to be above or below the
setpoint by this amount to initiate heat or cool modes.

0.1-10

Vestibule
Temp Sensor
Calibration
Oﬀ set

AV:11

If the Vestibule Temperature Sensor is reading incorrectly
you can use this option to enter an oﬀ set temperature
to adjust the Sensor’s Temperature.

-100-100

Leaving
Water Sensor
Calibration
Oﬀ set

AV:12

If the Leaving Water Sensor is reading incorrectly
you can use this option to enter an oﬀ set temperature
to adjust the Sensor’s Temperature.

-100-100

Entering
Water Sensor
Calibration
Oﬀ set

AV:13

If the Entering Water Sensor is reading incorrectly
you can use this option to enter an oﬀ set temperature
to adjust the Sensor’s Temperature.

-100-100

Outdoor
Air Sensor
Calibration
Oﬀ set

AV:14

If the Outdoor Air Sensor is reading incorrectly
you can use this option to enter an oﬀ set temperature
to adjust the Sensor’s Temperature.

-100-100

Comp Ratio
Setpoint for
Condenser
Speed

AV:15

The Condenser Fan Speed is controlled by the highest
Pressure Ratio from the active compressors.

0.5-3

Comp Ratio
Startup for
Compressors

AV:16

During Compressor Startup, the Pressure Ratio must be
below this setpoint.

0.5-3

Override Start/
Stop On

AV:17

Mechanical Cooling will be locked out if the
Outdoor Air Temperature is below this setpoint.

0-1

Override
Outdoor Air
Temperature

AV:18

Mechanical Heating will be locked out if the
Outdoor Air Temperature is above this setpoint.

-100-150

-100 = No

Override

Содержание SS1113






























































Результаты поиска

Содержание SS1113

Отзывы:

Бренды по названию

Популярные бренды

AAON SS1113, Техническое руководство

Результаты поиска

Содержание SS1113

Отзывы:

Бренды по названию

Популярные бренды