AAON SS1113 Скачать руководство пользователя страница 46

Страница: 46 / 62

APPENDIX A - COMPRESSOR CIRCUIT MODULE LED SCREENS

Main Chiller Controller Technical Guide

Main Screens Map

Refer to the following map when navigating through the LCD Main
Screens. To scroll through the screens, press the

<MENU>

button.

TBCOR 1

1808cXXX

SYSTEM
STATUS

SENSOR
STATUS

TURBOCOR

INFO

ALARMS

Press to scroll through SYSTEM STATUS Screens.

Press to scroll through SENSOR STATUS Screens.

Press to go to SENSOR STATUS Screen.

Press to go to TURBOCOR INFO Screen.

Press to go to ALARMS Screen.

Press to go to SYSTEM STATUS Screen.

Press to scroll through TBCOR MODULE Screens.

Press to scroll through TURBOCOR INFO Screens.

Press to scroll through ALARMS Screens.

Main Screen Map & Module Screens

Module Screens

Refer to the following map when navigating through the Compressor
Circuit Module Screens. From the TBCOR MODULE Screen, press

<ENTER>

to scroll through the screens.

TBCOR 1

1808cXXX

E-BUS

+###

SOFTWARE

1808cXXX

ADDRESS

# (#)

CURRENT BOARD ADDRESS

Conﬁ gure the address according to which circuit

this module represents—1=A, 2=B, 3=C

Number in parentheses is E-BUS address.

Module 1’s address is 1, Module 2’s address is 2,

Module 3’s address is 3

E-BUS COMMUNICATION DIAGNOSTICS

Number of COMM packets received.

Press to return to the TBCOR Screen.

Содержание SS1113






























































Результаты поиска

Содержание SS1113

Отзывы:

Бренды по названию

Популярные бренды

AAON SS1113, Техническое руководство

Результаты поиска

Содержание SS1113

Отзывы:

Бренды по названию

Популярные бренды