AAON SS1079 Скачать руководство пользователя страница 59

Страница: 59 / 98

VCC-X Operator Interface SD

VCC-X STATUS

VCC-X Status Screens

Status Screen #14 - PREHEAT-X Controller

Current Leaving Air and Entering Air

Temperature

VCC-X v1.02 ID #

Preheat-X Temps

Leaving Air: 0.0

Entring Air: 0.0

Line 3 Current PREHEAT-X Leaving Air Temperature

If the Preheat-X Controller (and the associated Leaving

Air Temperature Sensors) is installed and con

gured,

this line will display the current Preheat-X Leaving Air

Temperature.

Line 4 Current PREHEAT-X Entering Air Temperature

If the Preheat-X Controller (and the associated Entering

Air Temperature Sensor) is installed and con

gured, this

line will display the current Preheat-X Entering Air

Temperature.

Status Screen #15 - PREHEAT-X Controller

Modulating Position and Active Stages

VCC-X v1.02 ID #

Preheat-X Status

Mod Pos: XXX%
Active Stages: X

Line 3 Current PREHEAT-X Modulating Position

If you have a PREHEAT-X Controller connected to

the VCC-X Controller and are using Modulating Heat,

this is the current modulating heat signal

Line 4 Current PREHEAT-X Active Stages

If you have a PREHEAT-X Controller connected to the

VCC-X Controller, and are using staged heat, this is the

number of stages currently active.

Status Screen #16 - OA Drybulb and Humidity

VCC-X v1.02 ID #

Outdoor Conditions

Drybulb: 0.0

Humidity:

XXX%

Line 3 Current Outdoor Air Drybulb

If an E-BUS Outdoor Air Temperature/Humidity Sensor

has been installed and con

gured on the VCC-X, the

current Outdoor Air Temperature will display on this

line. If the sensor fails, this line will display a

temperature that is half way between the Cooling and

Heating

Lockout

Setpoints.

Line 4 Current Outdoor Air Relative Humidity

If an E-BUS Outdoor Air Temperature/Humidity Sensor

has been installed and con

gured on the VCC-X, the

Outdoor Air Relative Humidity Percentage will appear

on this line. If not, this line will display 0%.

Status Screen #17 - OA Wetbulb and Dewpoint

VCC-X v1.02 ID #

Outdoor Conditions

Wetbulb: 0.0

Dewpoint: 0.0

Line 3 Current Wetbulb Temperature

If an E-BUS Outdoor Air Temperature/Humidity Sensor

has been installed and con

gured on the unit, this line

will display the calculated Outdoor Air Wetbulb

Temperature. If not, it will display 0°F.

Line 4 Current Calculated Outdoor Air Dewpoint
Temperature

If an E-BUS Outdoor Air Temperature/Humidity Sensor

has been installed and con

gured on the unit, the

calculated Outdoor Air Dewpoint Temperature will

appear on this line. If not, this screen displays 0

Содержание SS1079



































































































Результаты поиска

Содержание SS1079

Отзывы:

Похожие инструкции для SS1079

Бренды по названию

Популярные бренды

AAON SS1079, Техническое руководство

Результаты поиска

Содержание SS1079

Отзывы:

Похожие инструкции для SS1079

Бренды по названию

Популярные бренды