AAON RSM-DEV1 Скачать руководство пользователя страница 30

Страница: 30 / 40

RSM-DEV1 Technical Guide

LCD SCREENS

Screen Descriptions

Danfoss VFD Screens

Refer to the following map and table when navigating through the

Danfoss VFD screens. From the DANFOSS VFD screen, press

<ENTER>

to scroll through the screens.

I LIMIT

XXX.XAMP

CURRENT

XX.X A

ALARMS

C1 HOURS

XXX

VFD HRS

XXX

MODEL #

XXXXXXXX

DRIVE#

XXXXXXXX

DANFOSS VFD SCREENS

Screen Text

Description

DANFOSS

COMP

Danfoss VFD status screens

CONNECT?

YES

VFD is connected and communicating. Options are:

•

YES

• NO

MB RETRY

XXXX

Totals if it is missing communication packet infor-

mation.

MB VALID

XXXX

Totals if it receives good communication packet

information.

VFD STAT

VFD compressor status. Displays a value read from

VFD showing status and configuration information.

It will display each bit of information separately.

COMMAND%

XXX%

Compressor percentage commanded to VFD.

MAX REF

XXXX RPM

Maximum speed programmed into the VFD in

RPM.

MIN REF

CONFIRMD

Minimum speed programmed into the VFD. Options

are

•

NOT = 0!

• CONFIRMD

For proper speed command this should always say

CONFIRMD, meaning it is set to zero.

ALARMS

Alarm codes read from the VFD. Will show NO

ALARMS if no alarms have occured or the alarm

code

I LIMIT

XXX.XAMP

I LIMIT

Measured in amps

CURRENT

XX.X A

CURRENT

Live current read from VFD in amps.

C1 HOURS

Compressor running hours read from VFD.

VFD HRS

VFD running hours read from VFD.

MODEL #

XXXXXXXX

Compressor model number read from VFD. Op-

tions are:

• VZH088

• VZH117

• VZH170

• VZH028

• VZH035

• VZH044

• VZH052

• VZH065

•

UNKNOWN!

If UNKNOWN is shown, check that proper unit is

selected in Prism 2.

DRIVE#

XXXXXXXX

Drive number. Options are:

• CDS803

• CDS303.

Table 13: Danfoss VFD Screens

DANFOSS

VFD

CONNECT?

YES

MB RETRY

XXXX

MB VALID

XXXX

VFD STAT

COMMAND%

XXX%

MAX REF

XXXX RPM

MIN REF

CONFIRMD

Содержание RSM-DEV1









































Результаты поиска

Содержание RSM-DEV1

Отзывы:

Бренды по названию

Популярные бренды

AAON RSM-DEV1, Техническое руководство

Результаты поиска

Содержание RSM-DEV1

Отзывы:

Бренды по названию

Популярные бренды