background image

12 
 

Input Voltage and Input Current 

The drives are designed for rated AC power 
supply: 50/60Hz, 380-480V on EV20XXM 
KX-XXX models and 208-240V on 
EV20XXM-JX-XXX drive models.  
 

Drive 

AC Input Overcurrent 

Protection 

EV2080J 

24A RMS 

EV2080K 

15A RMS 

EV2055J 

18A RMS 

EV2055K 

12A RMS 

 

Power Factor Correction 

Drive has passive power factor correction, 
which is capable of improving efficiencies. 

Speed Control  

The frequency range of the drive is from 
15Hz to 120Hz. If the frequency set by unit 
controller is less than 15Hz but not zero, 
then the compressor will work at 15Hz. 
Similarly, if the frequency set by unit 
controller is greater than 120Hz, then the 
compressor will work at 120Hz. 
 
There are three cases for unit shut down. 
  
Case I (Controlled shut down):  Unit shut 
down the compressor.  
 
Case II (Faulted condition): When drive 
faults occur, the drive will shut down the 
compressor. Major and minor faults have 
different shutdown sequences. For major 
faults, the drive trips the compressor 
immediately (from running frequency to 
zero frequency). For minor faults, it has the 
same sequence as Case I. As mentioned 
above clear faults using the 'Fault Clearing' 
method shown below. 
 
Case III: Loss of power shut down, this 
control procedure is the same as major fault 
shut down. 

Fault Clearing 

Faults are cleared through unit controls 
interface.  

Status Indication 

There are two control chips on the drive 
board and all of them have their own LED 
for status display. COMMS MCU has three 
LED indicators, DSP has one LED indicator. 

LED for COMMS MCU 
 

Operation Indicating LED  
(Green LED805) 

When the drive is in normal state (no 
protection and fault), the drive is in standby 
state and the compressor does not work, the 
LED will blink every 2 seconds. If the 
compressor is running, the LED will always 
be on. 
 

Protection Indicating LED  
(Yellow LED804) 

When the drive is under protection, the 
yellow LED will blink. Refer to 

Troubleshooting Table

 more information. 

 

Hardware Fault Indicating LED  
(Red LED803) 

When the drive is under hardware fault, the 
red LED will blink. Refer to 

Troubleshooting Table

 for more 

information. 
 

LED for Drive Control DSP Chip  
(Green LED802)  

When the drive is in normal state, whether 
the compressor is running or standby, the 
LED will blink every 1 second. When the 
drive is under protection or hardware fault, 
the LED will blink every 1/8 of a second.

 

Содержание RQ SERIES





































Отзывы: