manualshive.com logo in svg

AAON MODGAS-XWR2-B, Техническое руководство

Поделиться
Скачать
AAON MODGAS-XWR2-B Скачать руководство пользователя страница 38

38

MODGAS-XWR2-B Technical Guide

TROUBLESHOOTING

Alarms

Troubleshooting Alarms

Mechanical Failure

•  Check relay outputs on the MODGAS-XWR2-B for  

18-30 VAC output.

•  Verify the SAT OPTIONS jumper settings on the 

MODGAS-XWR2-B for Supply Air Temperature Sensor.

•  Verify gas valve LED is solid. Try forcing valves (refer to 

Force Screens, page 32

).

•  Verify that the Supply Air Temperature Sensor is connected 

to SAT and GND on the MODGAS-XWR2-B (Stand-

Alone Mode) or to AI2 (VCB-X) or to AI3 (VCCX2) and 

GND on the main controller (Communications Mode).

•  Verify Supply Air Temperature Sensor probe is mounted 

correctly in supply duct.

•  Remove SAT and GND wiring from the MODGAS-

XWR2-B and ohm sensor out (this may indicate open or 

failed wiring).

Fail Mode - Supply Air Temperature Sensor Failure

•  Verify that the Supply Air Temperature Sensor is connected 

to the SAT and GND on the MODGAS-XWR2-B (Stand-

Alone Mode) or to AI2 (VCB-X) or to AI3 (VCCX2) and 

GND on the main controller (Communications Mode).

•  Remove SAT and GND wiring from MODGAS-XWR2-B 

and ohm sensor out (this may indicate open or failed 

wiring). 

•  Verify the SAT OPTIONS jumper settings on the 

MODGAS-XWR2-B for the Supply Air Temperature 

Sensor.

Fail Mode - SAT Cutoff

•  Remove SAT and GND wiring from the MODGAS-

XWR2-B and ohm sensor out (this may indicate open or 

failed wiring). 

•  With Supply Air Sensor disconnected from the MODGAS-

XWR2, set volt meter to DC volts and measure voltage 

between SAT and GND on board. 

•  Verify Supply Air Temperature Sensor reading in duct with 

3rd party temperature testing device.

Communications Loss

•  Check COMM LED on MODGAS-XWR2-B.
• 

Verify 18-30 VAC power to all interconnected AAON unit 

controllers.

•  Verify E-BUS connection between the MODGAS-

XWR2-B and associated AAON unit controllers.

• 

In Communications Mode, confirm the main MODGAS-

XWR2-B screens shows COMM MODE and the main 

controller’s MODGAS status screen displays MODGAS-

XWR2-B’s Position %.

Содержание MODGAS-XWR2-B













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды