background image

 

16 

AAON, Inc. 

www.aaon.com 

Customer Service Department 

2425 South Yukon Ave • Tulsa, OK 74107 
Phone: 918-583-2266 • Fax: 918-382-6364 

ALWAYS USE AAON SPECIFIED PARTS

 

 
To order parts from the AAON Parts store 
online go to www.aaonparts.com.    
 

EVAPORATIVE-COOLED 
CONDENSER 

 

• Evaporative cooling equipment rejects heat by 
evaporating a portion of the recirculated water 
spray and discharging it from the unit with the 
hot, saturated air. As the spray water evaporates, 
it leaves behind the mineral content and 
impurities of the supply water. If these residuals 
are not purged from the water distribution 
system, they will become concentrated and lead 
to scaling, corrosion, sludge build-up and 
biological fouling. 
• A water treatment monitoring and control 
system has been furnished with this unit. Be sure 
to read the complete manual that has been 
furnished. All water treatment is a combination 
of bleed water and chemical treatment for proper 
control of the residuals and to prevent any 
biological contamination. 

 

 

 
GENERAL INFORMATION 
 
Severe Service:  

The following recommended maintenance 
procedures are basic requirements for normal 
operating environments. For severe operating 
conditions, the frequency of inspection and 
service should be increased. Air containing 
industrial and chemical fumes, salt, dust, or other 
airborne contaminates and particulates will be 
absorbed by the recirculating water system and 

may form solutions and deposits harmful to the 
products and personnel. 
 

Safety:  

The recirculating water system contains chemical 
additives for water quality control and biological 
contaminants removed from the air by the 
washing action of the water. Personnel exposed 
to the saturated effluent, drift, or direct contact 
should use proper precaution. Proper location of 
the evaporative-cooled condenser requires good 
judgment to prevent the air discharge from 
entering fresh air intakes or to avoid allowing 
contaminated building exhaust from entering the 
condenser. 
 

 

 
Follow local and national codes in locating the 
evaporative-cooled condenser but as minimum 
the evaporative-cooled condenser sump must be 
15 feet from the nearest intake. 
 

 

 
 
 
 
 
 
 

Содержание CL SERIES









































Отзывы: