A&D FZ-1200CT Скачать руководство пользователя

Страница: 14 / 84

6. RESPONSE ADJUSTMENT

This function stabilizes the weight value, reducing the influence on weighing that is caused by drafts
and vibration at the place where the balance is installed.

The function has three stages as follows and can be changed by simple key operation.

Indicator Description

FAST

Fast response, but prone to drafts and vibration.
Good for target weighing.

MID.

SLOW

Slow response, but strong against drafts and vibration
Good for weighing which requires a stable display.

Operation

1 Press and hold the MODE key until RESPONSE is

displayed. And then, release the key.

2 Press the MODE key to select a rate of the response

adjustment. Either FAST, MID. or SLOW can be
selected.

3 After a few seconds of inactivity, or when the PRINT

key is pressed, the balance displays

end

. Then, it

returns to the weighing mode and displays the
updated response indicator. The

response indicator

remains displayed for a while.

Note
Setting the response rate automatically changes the
“Condition (

Cond

)” and “Display refresh rate (

5pd

)”

parameters of “Environment, Display (

ba5fnc

)” in the

function table, as shown below:

Indicator

Cond

(Condition)

5pd

(Display refresh rate)

FAST

(

10 times/second)

MID.

(5 times/second)

SLOW

(5 times/second)

When the balance is to be used with other setting
combinations, set each parameter in the function table.

Содержание FZ-1200CT





















































































Результаты поиска

Содержание FZ-1200CT

Отзывы:

Похожие инструкции для FZ-1200CT

Бренды по названию

Популярные бренды

A&D FZ-1200CT, Инструкция по эксплуатации

Результаты поиска

Содержание FZ-1200CT

Отзывы:

Похожие инструкции для FZ-1200CT

Бренды по названию

Популярные бренды