A&D FS-D Скачать руководство пользователя страница 14

Страница: 14 / 24

7. CALIBRATION

This function adjusts the scale (indicator) for accurate weighing.
Calibration must be done when the FS

D is initially connected to a load cell (base unit).

Calibration may also be required according the changes in the environment.

When the scale (indicator) has been moved.

When the ambient environment has

significantly changed.

For regular calibration.

Loose the lock screws on the rear side of the
display pod, and remove the (CAL) switch
cover. The calibration switch inside.

7-1. Calibration using a weight

1. Warm up the indicator with a weighing platform connected for at least half an hour.

Change the user function setting “

f01

” or place something on the platform to

disable the auto power-off function.

When turning the power on and the indicator may display

-------

press the

PRINT/ENT

key to proceed to the weighing mode.

2. Press and hold the calibration (CAL) switch until

Cal

appears, and release the switch.

Press and hold the

key for about 5 seconds, then you

can also enter the calibration mode

(when “

C01-0

” is set).

Press the

ON/OFF

key or (CAL) switch to exit without

calibration.

3. Press the

PRINT/ENT

key, then the gravity

acceleration value will be displayed.

It is not necessary to set the gravity acceleration value

when calibrating the indicator with a calibration weight
at the place where it is to be used. (See the next
section about the gravity acceleration correction.)

4. Press the

PRINT/ENT

key, then

Cal

will be

displayed.

5. Make sure that there is nothing on the platform, and wait

until the STABLE indicator turns on.

6. Press the

PRINT/ENT

key. The indicator inputs the

zero point, and the display shows

5pn

and the

weight value for calibration (SPAN calibration).

The weight value is equal to the capacity. When you

enter with “kg” or “g” mode, then the value is “kg”.
Entering with “lb” or “oz”, then “lb”.

-0

5pn

-00

Cal

-00

9.7985

-00

Cal

-000

30.00

CAL switch cover

Calibration (CAL) switch

Содержание FS-D

























Результаты поиска

Содержание FS-D

Отзывы:

Бренды по названию

Популярные бренды

A&D FS-D, Инструкции по установке

Результаты поиска

Содержание FS-D

Отзывы:

Бренды по названию

Популярные бренды