Aaeon SBC-598 Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 80

background image

48 SBC-598 User Manual

PM Timers

The following four modes are Green PC power saving functions
which are only user configureable when "User Defined Power
Management" has been selected. See above for the available
Power Management selections.

HDD Off After

When enabled and after the selected time of system inactivity, the
hard disk drive will be powered down while all other devices will
remain active.

Doze Mode

This sets the period of system inactivity after which the system
goes into Doze mode, the most limited power saving state. The
settings range from 20 seconds to 40 minutes and can be set
manually when power management is in User Define mode. The
default setting is Disabled. When the system goes into power
saving mode, power management will skip to the next mode in the
sequence if this is disabled.

Standby Mode

This sets the period of system inactivity after which the system
goes into Standby mode, the intermediate power saving state. The
settings range from 20 seconds to 40 minutes and can be set
manually when power management is in User Define mode. The
default setting is Disabled. When the system goes into power
saving mode, power management will skip to the next mode in the
sequence if this is disabled.

Suspend Mode

This sets the period of system inactivity after which the system
goes into Suspend mode, the maximum power saving state. The
settings range from 20 seconds to 40 minutes and can be set
manually when power management is in User Define mode. The
default setting is Disabled. When the system goes into power
saving mode, power management will skip to the next mode in the
sequence if this is disabled.

«
...
54
55
56
57
58
...
»

Содержание SBC-598

















































































Отзывы:

Нет отзывов

Похожие инструкции для SBC-598

IntelliJack NJ200

Бренд: 3Com Страницы: 4

Бренд: National Instruments Страницы: 11

Бренд: PaloAlto Networks Страницы: 2

Asynchronous SH7145F

Бренд: Renesas Страницы: 17

Бренд: Freescale Semiconductor Страницы: 921

Бренд: Paradyne Страницы: 85

Бренд: Usr Страницы: 2

Бренд: UNA AUTOMATION Страницы: 20

Бренд: Baicells Страницы: 10

Бренд: Cisco MERAKI Страницы: 4

UniFi WiFi BaseStation XG

Бренд: Ubiquiti Страницы: 19

Emotron OSTO 100

Бренд: CG Страницы: 112

netHOST NHST-T100

Бренд: hilscher Страницы: 75

Бренд: Harman Страницы: 24

Бренд: Renesas Страницы: 4

DTS 4020.timebridge

Бренд: Mobatime Страницы: 94

Бренд: Netequalizer Страницы: 14

Бренд: Allen-Bradley Страницы: 76

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды