Aaeon SBC-598 Скачать руководство пользователя страница 12

Страница: 12 / 80

4 SBC-598 User Manual

Floppy disk drive (FDD) interface: Supports up to two floppy disk drives,
5.25" (360KB and 1.2MB) and/or 3.5" (720KB, 1.44MB, and 2.88MB).

Multi-mode parallel ports: Configured to LPT1, LPT2, LPT3, or disabled.
Supports SPP, ECP, and EPP.

Serial ports: 2 RS-232 serial ports. Ports can be individually configured
as COM1, COM2, COM3, COM4, or disabled.

IrDA interface: Infared wireless communication with compatible devices.

Keyboard/mouse connector: 6-pin mini DIN connector supports standard
PC/AT keyboard and PS/2 mouse.

USB connectors: Dual USB connectors on board.

DMA channels: 7

Interrupt levels: 15

Watchdog Timer: Can generate a system reset, IRQ15, or NMI, and
supports selectable timeout interval (2 sec~128 min, 1 sec/step).

VGA controller: SiS 5598, 64-bit graphics engine integrated.

Power management: I/O peripheral devices support power saving and
doze/standby/suspend modes. APM 1.2 compliant

Display memory: Supports shared system memory up to 4MB.

Display type: Supports CRT display.

Resolution: Support up to 1024 x 768 @ 16.7M colors.

SSD interface: One 32-pin DIP socket supports the M-Systems DiskOn-
Chip 2000 series, memory capacity from 2MB to 72MB.

Power supply voltage:

+5V (4.75V to 5.25V)

Power Requirement:

Bare Board:

+5V @ 2A

Pentium MMX-200:

+5V @ 6A

AMD K6-233:

+5V @ 10A

Operating temperature: 32

F to 140

F (0

C to 60

Board size: 13.31" (L) x 4.8" (W) (338 mm x 122 mm)

Board weight: 0.88 lbs (0.4 kg)

Содержание SBC-598

















































































Результаты поиска

Содержание SBC-598

Отзывы:

Бренды по названию

Популярные бренды

Aaeon SBC-598, Руководство пользователя

Результаты поиска

Содержание SBC-598

Отзывы:

Бренды по названию

Популярные бренды