manualshive.com logo in svg

AAD 7001, Руководство пользователя, Страница: 8 / 10

Поделиться
Скачать
AAD 7001 Скачать руководство пользователя страница 8

1-7

Amplifier Power

We  recommend  that  you  use  an  amplifier  with  power  rating  at  least  a  100watt  RMS  or 

ideally 300watts plus per channel. These 7001s have a vast dynamic range and using a large 

power amplifier to power them will allow them to reach their full potential.

Amplifiers  with  up  to  1000  watts  RMS  output  can  produce  lifelike  dynamics  on  transients 

without stress or strain.

Headroom is not audible but a lack of it certainly is.

Each time you run your system you may need about 15minutes of initial playing before the 

sound starts to take on a dimension of breathtaking clarity.

The  7001s  will  even  reveal  how  your  amplifier  sounds  whether  it  is  just  turned  on  cold  or 

been running warm for a while.

Speakers Cables, Interconnects & Power Cords

 Due to their revealing nature, the 7001 speakers will discriminate between speaker cables 

and interconnects with ease. It will bring a new palette of colors to what you have ever heard 

before  to  your  recordings.  So  even  changing  between  cables  will  bring  changes  to  you 

sound. You should experiment to what is sounding to your idea of transparency.

Program Material

The  7001  is  neutral  when  it  comes  to  producing  sound.  It  is  not  slanted  to  any  side  of  the 

audio  spectrum.  It  will  therefore  reveal  more  about  the  recordings  and  the  process  of  how 

they were recorded more than the producer and artist who created them know.

SPECIFICATIONS

System Type

: 2 way loudspeaker 5 inch cone woofer, horn loaded ribbon tweeter.

Bass Loading

:  6.5 inch critically tuned passive radiator.

Crossover

:  12dB/Octave at 3 KHz

Low-Frequency  Transducer

:  Cast  magnesium  alloy  frame,  High  Flux  Neodymium-Iron- 

Boron  magnet  system,  High  Excursion  2-inch  Copper  Clad 

aluminum  voice  coil.  Aluminum  cone,  Butyl-Rubber 

surround.

High Frequency Transducer

: Neodymium magnet system. Horn loaded Aluminum ribbon

Cabinet: 

1.5  inch  thick  MDF  side  panels  with  lead  damping.0.5  inch Aluminum  front  and           

back panels

Frequency Response

: 25Hz-50KHz +/- 3dB (dependant upon room acoustics).

Impedance

: 8 Ohms Nominal.

Recommended Amplifier Power

: 100 watts minimum 1000 watts maximum. 

Содержание 7001











Отзывы:

Нет отзывов