manualshive.com logo in svg

A.O. Smith TWI 35-130, Инструкция по установке, эксплуатации и обслуживанию, Страница: 44 / 64

Поделиться
Скачать
A.O. Smith TWI 35-130 Скачать руководство пользователя страница 44

9.2 

 

Troubleshooting table for general errors

 

W

arning

 

Maintenance shall only be carr

ied out by a service and maintenance engineer

.

General errors

Instruction manual - 

TWI 35-130 G/TWI 45-190 G   

  

 

 

 

 

 

 

         44

Symptom

Cause

Solution

Remark

Gas smell

Gas leakage

W

arning

Immediately close the mains gas supply valve.

W

arning

Do not operate any switches.

W

arning

No open fire!

W

arning

Ventilate the area the device has been installed in.

W

arning

Immediately contact the installation engineer or the local gas  company

.

W

ater leakage

Leaking water con

-

nection (thread)

Tighten the threaded connection.

Contact the installation engineer if the leakage has not been  remedied.

Leakage of conden

-

sate

Check if condensate is discharged. Restore this if necessary

.

Leakage from  another water device  or pipe nearby

Find the leakage.

Leakage of the tank  of the device

Consult the supplier and/or the manufacturer

.

Содержание TWI 35-130

































































Отзывы:

Нет отзывов