A.O. Smith Product Preservers Powered Anode System, Руководство пользователя

Страница: 6 / 8

6 • Powered Anode System
SYSTEM FEEDBACK
LED Description/
Corrective
Action
Solid
(Green) System is opera ng
properly
(i.e., components are
installed properly, module
is powered, and the tank is
full of water).
1 Flash
(Red)* Anode disconnected.
Check for loose connec ons
and breaks in the wire
between the control
module and the anode/
tank. The tank connec on
must be to bare metal (i.e.,
not paint).
2
Flashes
(Red)* Anode shorted.
1.) Check for shorted wiring.
Correct wiring as necessary.
2.) Check for corrosion on
top of anode (electrode)
and clean with a brush.
3.) Anode may have
corrosion or contamina on.
Clean as described below.
WARNING!
Electric Shock Risk. Contact
with electrical components
can result in severe injury
or death from electrical
shock. Use a non-contact
circuit tester to con
fi rm that
power is o ff .
Turn o ff power to the
Powered Anode System.
Disconnect power to the
water heater if it is an
electric model. Remove the
anode and clean it with a
cloth.
3
Flashes
(Red)* Module failure. Replace the
control module.
* Beeper will sound during error code.
NOTICE:
• It will take about 20 seconds for the
system to indicate an error condi on.
• It may take several seconds for the
system to show correct opera on
a er correc ons are made.
REGULATORY
NOTICES
FCC (United States of America)
This equipment has been tested and
found to comply with the limits for
a Class B digital device, pursuant to
part 15 of the FCC rules. These limits
are designed to provide reasonable
protec on against interference in a
commercial installa on. This equipment
generates, uses, and can radiate
radio frequency energy and, if not
installed and used in accordance with
the instruc on manual, may cause
interference to radio communica ons.
However, there is no guarantee that
interference will not occur in a par cular
installa on. If this equipment does
cause interference to radio or television
recep on, which can be determined
by turning the equipment o
ff and on,
the user is encouraged to try to correct
the interference by one or more of the
following measures:
• Reorient or relocate the receiving
antenna.
• Increase the separa on between the
equipment and receiver.
• Connect the equipment into an outlet
on a circuit di ff erent from that to
which the receiver is connected.
• Consult the dealer or an experienced
radio/TV technician
CAUTION: Changes or modi fi ca ons to
this equipment not expressly approved
by the party responsible for compliance
(A.O. Smith) could void the user’s
authority to operate the equipment.
ICES-003 (Canada)
This Class B digital apparatus complies
with Canadian ICES-003.
Cet appareil numérique de la classe B
est conforme à la norme NMB-003 du
Canada.
SPECIFICATIONS
Environmental Speci fi ca ons:
• Humidity up to 95% non-condensing.
• Temperature, opera onal = -4°F to
158°F (-20°C to 70°C)
• Temperature, storage = -40°F to 176°F
(-40°C to 80°C)
• Vibra on = 0.5G
Power Supply (Provided):
Input 100-240VAC, 50-60Hz. 0.5A
Output 12V DC, 1.0A
Power Supply Requirements for
Powered Anode System:
12V @ 150mA
ASSISTANCE
For warranty ques ons, call:
800.527.1953
When calling, be ready to provide the
following informa
on: your name,
address, and telephone number; the
serial number of your Powered Anode
System; proof of purchase/installa on;
and a clear descrip on of the problem.