A.O. Smith LILY, Руководство пользователя

Страница: 13 / 56

ENG 11
Pre-Installation Preparations
• Choose the location where the water purifier will be installed
• Confirm the availability of the various tools required
for installation
• Confirm that you have all the connectors required for installation
• Make sure to turn off the water supply and electricity before
commencing installation
Warning: In places where inlet water pressure is more than 0.35 MPa(3,5
Bars), it is recommended to use a pressure reducer before the unit.
Installation Methods
Our company recommends that your water purifier is installed by trained professionals as the installation process is somewhat complex and requires the
use of various tools. However, if you decide to install the purifier yourself, please refer to the following steps and diagrams:
Adjustable Spanner
Drill
6.2 mm Drilling Bit
Hole Saw
φ
16-35 mm
T10 Cross and Flathead Screwdrivers
Scissors
14 - 16 mm Wrench
19 - 21 mm Wrench
Needle Nose Pliers
1
1
1 (Waste water hole)
1
1 of each
1 pair
1
1
1
Instructions for Proper Installation
• Installation of the inlet water metal hose and 3-way inlet water joint:
(If the metal hose diameter is equal or less than 9 mm, the 3 - way inlet
water joint should be connected to the unit) First, close the inlet water
valve. Screw off the metal hose. Remove the 3-way inlet water joint
from the water purifier accessories box, screw one end of the inlet water
3-way joint onto the inlet water valve outlet. One end of the unscrewed
metal hose should be screwed into the 3-way inlet water joint using the
screw nut (See Diagram 4)
•
Installation of the 3-way inlet water joint and inlet water ball valve:
Take out the inlet water ball valve from the water purifier accessories
box, wrap one end of the external threads on the ball valve with appro
priate teflon tape (See Diagram 5). If you have silica gel, spread a little
over the thread and then screw the ball valve into the corresponding hole
of the 3-way inlet water joint (See Diagram 5). Take out the Ø 9mm
water pipe from the accessories box. Using a pair of scissors, cut
a suitable length of pipe and connect one end of the pipe to
the inlet water ball valve (See Diagram 6). Finally screw the nut in place.
Diagram 4
Diagram 5
3-Way inlet
water joint
Inlet water
ball valve
Teflon tape
Water pipe
connection
Diagram 6
9mm Ball valve
Inlet water
3-way
joint
ENG 11
Pre-Installation Preparations
for installation
Make sure to turn off the water supply and electricity before
commencing installation
Installation Methods
Our
Adjustable Spanner 1
Drill 1
6.0 mm Drilling Bit 1 (Waste water hole)
Hole Saw φ16-35mm 1 (High-speed steel or marble hole saw)
T10, Cross, Flathead Screwdriver 1 of each
Scissors
1 pair
14 - 16 mm Wrench 1
19 - 21 mm Wrench 1
Needle Nose Pliers 1
Instructions for Proper Installation
Inlet water metal hose and 3-way inlet water joint installation method(if the
metal hose diameter is 9mm, the 3-way inlet water joint must be purchased
separately)
Before installing, c lose the inlet water valve. U nscrew the inlet water valv from t
he metal hose. R emove the inlet water 3-way joint from the water purifier
accessories box. Thread one end of the inlet water 3-way joint into the inlet water
va lve outlet connection. O ne e nd of the metal hos e should be connected to the
external threads o f the inlet water three-way joint (see diagram 6).
2) Inlet tube installation
Take out the 1/4” tube from the accessory box, and cut to suitable length with
scissors, connect one end of the inlet tube to the inlet end of the 3-way joint (see
diagram 6), then screw the nut tightly. The other end of inlet tube connect to
the “Source” of the unit connector.
Note to fix the tube and quick connector to avoid water leakage issues.
1）
Diagram 6