A.O. Smith FPD SEALED SHOT страница 1 Скачать руководство пользователя

Страница: 1 / 20

FPD SEALED SHOT

W I T H

HOT SURFACE

IGNITION AND

SMART VALVE

CAUTION: TEXT PRINTED OR OUTLINED IN RED

CONTAINS INFORMATION RELATIVE TO YOUR SAFETY.

PLEASE READ THOROUGHLY BEFORE INSTALLING AND

USING THIS APPLIANCE.

KEEP THIS MANUAL IN THE POCKET ON HEATER FOR FUTURE REFERENCE

WHENEVER MAINTENANCE ADJUSTMENT OR SERVICE IS REQUIRED.

PRINTED IN U.S.A. 2556 1299

PART NO. 183399-000
SUPERSEDES 183097-000

Thank you for buying this energy efficient water heater from
A.O. Smith Water Products Company. We appreciate your
confidence in our products.

You should thoroughly read this manual before installation
and/or operation of this water heater. Please pay particular
attention to the important safety and operating instructions
as well as the WARNINGS and CAUTIONS.

RESIDENTIAL

GAS WATER HEATERS

OWNER'S MANUAL

A DIVISION OF A.O. SMITH CORPORATION

www.hotwater.com

GET TO KNOW YOUR WATER HEATER

GENERAL SAFETY INFORMATION

INSTALLATION

3-14

OPERATION

14-16

MAINTENANCE AND
TROUBLESHOOTING

17-19

WARRANTY

TABLE OF CONTENTS

PAGE

Содержание FPD SEALED SHOT





















Результаты поиска

Содержание FPD SEALED SHOT

Отзывы:

Похожие инструкции для FPD SEALED SHOT

Бренды по названию

Популярные бренды

A.O. Smith FPD SEALED SHOT, Руководство пользователя

Результаты поиска

Содержание FPD SEALED SHOT

Отзывы:

Похожие инструкции для FPD SEALED SHOT

Бренды по названию

Популярные бренды