background image

5

5

Check all connections for leaks.  Consult the local utility company to examine installation for propriety and safety.

SENSOR

WIRES

6” AIR GAP

TO SUITABLE

DRAIN

MIXING

VALVE

SUITABLE DRAIN PAN

AT LEAST 2” GREATER

THAN THE DIAMETER

OF THE WATER HEATER.

TANK SENSOR STUD

ACCESS COVER

TANK SENSOR STUD

WATER INLET

SHUTOFF

VALVE

DRAIN

VALVE

COLD

WATER

INLET

TEMPERED

WATER

OUTLET

TO PUMP

(SOLAR LOOP)

(ALTERNATE)

TO PUMP

(SOLAR LOOP)

FROM

COLLECTOR

(SOLAR LOOP)

(ALTERNATE)

FROM

COLLECTOR

(SOLAR LOOP)

TEMPERATURE

PRESSURE

RELIEF VALVE

DISCHARGE PIPE

(DO NOT PLUG)

HEATING ELEMENT

ACCESS COVER

ELECTRICAL

JUNCTION BOX

INSTALL THERMAL EXPANSION

TANK IF WATER HEATER IS

INSTALLED IN A CLOSED

WATER SYSTEM

VACUUM RELIEF

VALVE

INSTALL PER

LOCAL CODES

Figure 1.

TYPICAL INSTALLATION

Water (Potable) Heating:

 All models are considered suitable 

for water (potable) heating only.

HOTTER WATER CAN SCALD: 

Water heaters are intended to produce hot water. Water heated to a 

temperature which will satisfy space heating, clothes washing, dish 

washing, and other sanitizing needs can scald and permanently injure 

you upon contact. Some people are more likely to be permanently 

injured by hot water than others. These include the elderly, children, 

the infirm, or physically/mentally disabled. If anyone using hot water 

in your home fits into one of these groups or if there is a local code 

or state law requiring a certain temperature water at the hot water 

tap, then you must take special precautions. In addition to using 

the lowest possible temperature setting that satisfies your hot water 

needs, a means such as a mixing valve should be used at the hot 

water taps used by these people or at the water heater. Mixing valves 

are available from your local plumbing contractor. Consult a Qualified 

Installer or Service Agency. Follow mixing valve manufacturer’s 

instructions for installation of the valves. Before changing the factory 

setting on the thermostat, read the “Temperature Regulation” section 

in this manual.

Содержание Cirrex SUN-80





















Отзывы: