background image

35

6 Maintenance Instructions 

6.1 General 

1. The maintenance of the water heater includes cleaning the tank and cleaning up the scales 

on the heating elements, especially in the area with harder water. It is recommended that the 

tank to be cleaned every month. Check the scales on the inner surface of the tank and the 

surface of the elements to determine whether cleaning is necessary, and the cleaning of 

heating elements should be performed by local supplier. It is normal if there is a hissing 

during the cleaning. 

2. The temperature and pressure relief valve should be inspected every month to ensure it is 

in effective operation. Pull the handle of the relief valve several times to ensure the valve can 

switch freely. Please pull the handle of the relief valve once every month, and discharge 4~8L 

water, which can prevent scaling inside of the relief valve. 

3. The water heater is equipped with an anode to protect the enamel water tank from 

corrosion through electrolysis. When the material of the anode is consumed completely, the 

water tank would lose this protection. The anode should be checked once every year to 

determine the consumption of the material or change the new one. When the anode diameter 

is less than 1 cm, change it for a new one. Higher water temperature and softer water can 

accelerate the consumption of the anode, so the anode should be checked more frequently. 

Anode is a consumptive part and is charged for replacement as it is not covered by 

guarantee. 

4. The water heater is recommended to operate in the surrounding that is free from too much 

dust. 

6.2 Cleaning the Water Heater 

The drain valve of the water heater should be opened regularly to prevent precipitation 

on the bottom of the tank. 

1. Disconnect the power supply to the water heater. 

2. Connect a soft tube at the drain valve outlet and put the other end to a floor drain. Turn the 

handle of the drain valve to the left (anti-clockwise) to open the drain valve. Drain the water 

completely. If there is no water flowing out after opening the drain valve, perform according to 

the instruction of cleaning the precipitation. 

CAUTION: 

This water heater should be maintained by a qualified person. Failure to follow 

these instructions can result in severe injury or property loss. 

WARNING:

 Disconnect the power supply to the water heater before maintaining the water 

heater. 

CAUTION: 

When inspecting the T&P relief valve, the water outlet temperature of the valve 

might be high and it could cause severe scalds, so be careful. 

Содержание CAHP-120 Series















































Отзывы: