A.O. Smith BTI - 65 страница 6 Скачать руководство пользователя

Страница: 6 / 26

1129

1.2 Technical safety

equipment

1.2.1 Gas control valve

The water heater is equipped with a gas

control wich regulates the flow of gas to

the burner. The gas block is equipped

with a safety valve, gas valve and burner

control (on a standard natural gas

setting). To ensure improved ignition the

gas control valve opening mechanism is

fitted with a delay (softlite).

The gas control block is suitable for

gasses from the first, second and third

gas family. The maximum inlet pressure

is 60 mbar.

The automatic incandescent ignition (hot

surface) ensures that the burner ignites

as soon as there is a demand for heat.

1.2.2 control panel

Temperature control for the water heater

is housed in the control panel (See figur

2). For safety purposes, heaters are

always fitted with two thermostats: a

control thermostat is adjustable between

40 °C and 80 °C and a safety thermostat

90 °C. The control panel is fitted with

an ON/OFF switch (I/0). At setting

”I”, the gas control is activated on the

basis of heat demand from the control

thermostat. At setting ”0” the heater is

switched off.

A) Hot water outlet

B) Cold water inlet

1) Electrical connection

2) ON/OFF switch

3) Ignition controller reset button

4) Control thermostat knob

5) Safety thermostat reset button

Figur 2 - Top view of the heater

Содержание BTI - 65



























Результаты поиска

Содержание BTI - 65

Отзывы:

Похожие инструкции для BTI - 65

Бренды по названию

Популярные бренды

A.O. Smith BTI - 65, Инструкция по установке и эксплуатации

Результаты поиска

Содержание BTI - 65

Отзывы:

Похожие инструкции для BTI - 65

Бренды по названию

Популярные бренды