background image

   Installation & Operation Manual

Models:  400 - 2100

This manual supplies information for the 
installation, operation, and servicing of the 
appliance.  It is strongly recommended that 
this manual and the Genesis Service Manual be 
reviewed completely before proceeding with an 
installation.  Perform steps in the order given.  
Failure to comply could result in severe personal 
injury, death, or substantial property damage.

 WARNING:

Save this manual for future reference.

GNS-I-S Rev A

-- Do not store or use gasoline or other flammable vapors and 
     liquids in the vicinity of this or any other appliance.

-- 

WHAT TO DO IF YOU SMELL GAS

•  Do not try to light any appliance.
•  Do not touch any electrical switch; do not use any phone in your 
 building.
• Immediately call your gas supplier from a near by phone. 

 

  Follow the gas supplier’s instructions.
•  If you cannot reach your gas supplier, call the fire department.
-- Installation and service must be performed by a qualified 
    installer, service agency, or the gas supplier.

WARNING:

  

If the information in these instructions is not 

followed exactly, a fire or explosion may result causing property 
damage, personal injury or death.

Содержание 400 - 2100









































































Отзывы: