background image

lImIteD warranty

Equipment manufactured by Roundup Food Equipment Division of A.J. Antunes & Co. has been con

-

structed of the finest materials available and manufactured to high quality standards.  these units are 

warranted to be free from electrical and mechanical defects for a period of one (1) year from date of 

purchase under normal use and service, and when installed in accordance with manufacturer’s recom-

mendations.  to insure continued operation of the units, follow the maintenance procedures outlined in 

the Owner’s Manual.  During the first 12 months, electro-mechanical parts, non-overtime labor, and trav

-

el expenses up to 2 hours (100 miles/160 km), round trip from the nearest authorized service center 

are covered.

1. this warranty does not cover cost of installation, defects caused by improper storage or handling prior to 

placing of the Equipment.  this warranty does not cover overtime charges or work done by unauthorized 

service agencies or personnel.  this warranty does not cover normal maintenance, calibration, or regular 

adjustments as specified in operating and maintenance instructions of this manual, and/or labor involved 

in moving adjacent objects to gain access to the equipment.  this warranty does not cover consumable/

wear items. this warranty does not cover damage to the Load cell or Load cell assembly due to abuse, 

misuse, dropping of unit/shock loads or exceeding maximum weight capacity (4 lbs).  this warranty does 

not cover water contamination problems such as foreign material in water lines or inside solenoid valves.  

it does not cover water pressure problems or failures resulting from improper/incorrect voltage supply.   

this warranty does not cover travel time & Mileage in excess of 2 hours (100 miles/160 km) round trip 

from the nearest authorized service agency. 

2. Roundup reserves the right to make changes in design or add any improvements on any product.  the 

right is always reserved to modify equipment because of factors beyond our control and government 

regulations.  changes to update equipment do not constitute a warranty charge.

3. if shipment is damaged in transit, the purchaser should make a claim directly upon the carrier.  careful inspec-

tion should be made of the shipment as soon as it arrives and visible damage should be noted upon the car-

rier’s receipt.  Damage should be reported to the carrier.  This damage is not covered under this warranty.

4. Warranty charges do not include freight or foreign, excise, municipal or other sales or use taxes.  all such 

freight and taxes are the responsibility of the purchaser.  

5. 

THIS  WARRANTy  IS  ExCLuSIvE AND  IS  IN  LIEu  OF ALL  OTHER  WARRANTIES,  ExPRESSED 

OR  IMPLIED,  INCLuDING ANy  IMPLIED  WARRANTy  OR  MERCHANTABILITy  OR  FITNESS  FOR 

A PARTICuLAR PuRPOSE, EACH OF WHICH IS HEREBy ExPRESSLy DISCLAIMED.  THE REM

-

EDIES  DESCRIBED ABOvE ARE  ExCLuSIvE AND  IN  NO  EvENT  SHALL  ROuNDuP  BE  LIABLE 

FOR  SPECIAL  CONSEQuENTIAL  OR  INCIDENTAL  DAMAGES  FOR THE  BREACH  OR  DELAy  IN 

PERFORMANCE OF THIS WARRANTy.

Содержание Roundup VS-200A-A1

















Отзывы: