A.J.Antunes 9210606 Скачать руководство пользователя

Страница: 6 / 28

Rapid toasteR VCt-250

P/N 00837 Rev. L 03/07

McDonald’s

location

When placing the toaster into service, pay attention to

the following guidelines.

• Make sure power to the unit is off and the toaster

is at room temperature.

• Do not block or cover any openings on the unit.

• Do not immerse cord or plug in water.

• Keep cord away from heated surfaces.

• Do not allow cord to hang over edge of table or

counter.

Connect the unit to the power supply. Refer to the

specification plate for the proper voltage.

WaRNiNG

eleCtRiCal shoCK haZaRd. failURe to

folloW the iNstRUCtioNs iN this MaNUal

CoUld ResUlt iN seRioUs iNjURY oR death.

• electrical ground is required on this appliance.
• do not modify the power supply cord plug. if

it does not fit the outlet, have a proper outlet

installed by a qualified electrician.

• do not use an extension cord with this appli-

ance.

• the toaster should be grounded according to

local electrical codes to prevent the possibil-

ity of electrical shock. it requires a grounded

receptacle with separate electrical lines, pro-

tected by fuses or circuit breaker of the proper

rating.

• Check with a qualified electrician if you are in

doubt as to whether the appliance is properly

grounded.

CaUtioN

bread may burn. therefore toasters must not be

used near or below curtains or other combustible

walls and materials. failure to maintain safe oper-

ating distances may cause discoloration or com-

bustion.

CaUtioN

all electrical connections must be in accordance

with local electrical codes and any other appli-

cable codes.

Unpacking

. Remove unit and all packing materials from

shipping carton.

2. Open the accessory box. It should contain

the following:

• Bun Chute (Figure )

• Bun Feeder (Figure )

• Plastic bag containing the

Release Sheets (not shown)

3. Remove all packing materials and protective

coverings from the unit and parts.

Note: if any parts are missing or damaged, con-

tact a.j. antunes technical service iMMediatelY

at 1-877-392-7854 (North america only), or 630-784-

1000.

iNstallatioN

figure 1. installing bun Chute

POWER

TEMP

DOWN

TEMP

SCALE

°C

°F

CAUTION

Bun Chute

Bun Feeder

hook Bun Chute over

rear Conveyor Cover

Rod

assembling the Unit

. Install the Bun Chute (Figure ).

2. Install the Bun Feeder. The Bun Feeder clips fit

over the tip of the Platen and retain the Release

Sheet (Figures & 9).

Note: Check the Release sheet to make sure it

is not caught in the conveyor. additional Release

sheets can be obtained through your authorized

service agency.

Содержание 9210606





























Результаты поиска

Содержание 9210606

Отзывы:

Похожие инструкции для 9210606

Бренды по названию

Популярные бренды

A.J.Antunes 9210606, Руководство пользователя

Результаты поиска

Содержание 9210606

Отзывы:

Похожие инструкции для 9210606

Бренды по названию

Популярные бренды