A.J.Antunes 9210606 Скачать руководство пользователя

Страница: 12 / 28

Rapid toasteR VCt-250

P/N 00837 Rev. L 03/07

McDonald’s

figure 11. Replacing belt Wraps

ION

POW

TEMP

DOW

TEMP
UP

TEM

SCAL

˚C

˚F

Bun Feeder

Front (heel) Conveyor Cover

Rear (Crown)

Conveyor Cover

Bun Chute

Safety

Interlock

Switch

( each side)

MaiNteNaNCe (continued)

Monthly: bun temperature test

Note: the minimum temperature allowed is 150°

f (65.6º C). if this temperature is not achieved con-

tact your authorized service agency.

tools Required:

Pyrometer/Needle probe attachment,

four 8 oz. coffee cups stacked together, plus one lid

or four 2 oz coffee cups plus one lid.

. Turn the Rocker Switch (power On/Off) to ON and

allow the unit to preheat for 30 minutes.

2. Toast 3 regular buns (to be used with the 8oz.

cup stack) or 4 regular buns (to be used with the

2 oz. cup stack).

3. Immediately stuff the buns into the stacked cups

and tightly apply the lid. Wait for 0 minutes.

4. Insert the needle probe attachment of the

pyrometer through the lid several times.

Note the maximum temperature.

Monthly: Replace Release sheet.

every three Months: Replace belt Wraps,

Clean and Measure Conveyor belt Chains,

Check Roller tensioners, and Check

temperature of bun landing area.

Remove the Belt Wraps & Release Sheet.

. Turn the unit OFF, unplug the toaster, and allow it

to cool down.

2. Remove the Bun Feeder, Bun Chute, and change

the Bun Thickness Compression Controls to

“F & 6” (Figure 2a and 2b).

3. Remove and discard the black Release Sheet.

4. Open the Front (heel/Club) Conveyor Cover and

rotate the Belt Wrap so its flap is in the middle

(top to bottom) of the conveyor. Pull the hinge

pin out of the Belt Wrap and then remove and

discard this Belt Wrap. Repeat this process on

the Rear (Crown) side.

Clean the Conveyor belt Chains

. Spray

Mcd© all-purpose super Concentrate

(hCs)

on a clean, dry, towel and wipe the sur-

face of the Rear (Crown) Conveyor Belt Chain

links firmly from side to side and top to bottom.

Immediately repeat this procedure with a clean,

dry, towel dampened with

KaYQUat™ sanitizer

(hCs)

solution and repeat this procedure on the

Front (heel/Club) Conveyor Belt chain.

2. Close the Conveyor Cover(s), plug in the power

cord, turn on the unit, count to ten (0) seconds

for MFG# 920606, count thirteen (3) seconds

for MFG# 92066. For MFG# 920607, 608,

63, 65, 624, & 626 count to seventeen (7)

seconds. Next, turn the unit OFF and unplug the

power cord.

Note: Refer to figure 2 in the operation section of

this Manual.

3. Open the Conveyor Cover(s) and repeat Step

to clean the other half of both the Front (heel/

Club) and Rear (Crown) Conveyor Belt Chains.

Содержание 9210606





























Результаты поиска

Содержание 9210606

Отзывы:

Похожие инструкции для 9210606

Бренды по названию

Популярные бренды

A.J.Antunes 9210606, Руководство пользователя

Результаты поиска

Содержание 9210606

Отзывы:

Похожие инструкции для 9210606

Бренды по названию

Популярные бренды