A.J.Antunes 9100320 Скачать руководство пользователя страница 15

Страница: 15 / 24

P/N 1010751 Rev. G 01/08

McDonald’s

Multi-purpose steaMer Mps-250

diaGNostiCs (continued)

DOWN

PROGRAM SINGLE SHOT

ERR

err

(Error) will be displayed when there are program-

ming parameter errors. If this message appears, you

may have to clear the current parameters.
To clear the unit’s current programming and reset the

unit to its’ factory default settings:

1. Turn the unit off.

2. Push the

start/stoP

and

doWN arroW

keys simultaneously and, while turning the unit

back on continue to hold them until you hear the

unit BEEP (and then stops).

3. Check the Display.

• If the Display shows “ERR” again, contact

Roundup for technical assistance.

• If the Display appears normal, try both a

single shot and factory default timed cycles

before attempting to reprogram the unit.

Review the Programming section of this manual (Page

8) and then program the Menu Channel Buttons

according to your cooking requirements.

The TEMP Display indicates that the control cabinet

temperature has exceeded 155ºF (68ºC). If this occurs,

the unit must be turned off for at least 20 minutes so

that it can cool off and reset.

If this condition reoccurs, contact your Authorized

Service Agency or Roundup Technical Assistance.

The control board monitors the control cabinet ambient

temperature and records whatever its highest tempera-

ture has been. Your service technician could find such

information very useful when troubleshooting the unit.

To determine what the control cabinet’s highest tem-

perature has been since it was last reset:

1. Turn the unit off.

2. Turn the unit back On while pressing both the

and

doWN arroWs

at the same time.

3. Read the highest control cabinet temperature

recorded on the display and release the arrow

keys.

4. Turn the unit off again to preserve this record.

To clear/reset this record, press both the

and

doWN arroWs

and

ProGraM

button simultane-

ously (before turning the unit off) and the display will

show 33ºF - indicating that the record has been cleared

- and then turn the unit off.

DOWN

PROGRAM SINGLE SHOT

TEMP

teMP

indicates the control cabinet temperature has

exceeded 155°F (68°C) causing the unit to shut down.

DOWN

PROGRAM SINGLE SHOT

POWER

00:10

To change the Setpoint temperature, press and hold

the

and

doWN

arrows simultaneously for three

seconds. Then, raise or lower the temperature by

Pressing the

doWN

arrows. Minimum tempera-

tures should be 375°F (191° C).

DOWN

PROGRAM SINGLE SHOT

POWER

00:10

To check the GENERATOR temperature, press and

hold the

arrow

. The display will read the set tem-

perature.

Содержание 9100320

























Результаты поиска

Содержание 9100320

Отзывы:

Бренды по названию

Популярные бренды

A.J.Antunes 9100320, Руководство пользователя

Результаты поиска

Содержание 9100320

Отзывы:

Бренды по названию

Популярные бренды