background image

warranty information

LIMITED TWO YEAR CONSUMER WARRANTY

Directed Electronics, Inc. promises to the original purchaser, to replace this product should it prove to be
defective in workmanship or material under normal use, for a period of two years from the date of
purchase by the dealer as indicated by the date code marking of the product 

PROVIDED

the product was

installed by an authorized Directed dealer. During this two year period, there will be no charge for this
replacement 

PROVIDED

the unit is returned to Directed, shipping pre-paid.  If the unit is installed by

anyone other than an authorized Directed dealer, the warranty period will be 1 year from date of purchase
by the dealer as indicated by the date code marking of the product. During this 1 year period, there will
be no charge for this replacement 

PROVIDED

the unit is returned to Directed, shipping pre-paid. This

warranty is non-transferable and does not apply to any unit that has been modified or used in a manner
contrary to its intended purpose, and does not cover damage to the unit caused by installation or removal
of the unit. This warranty is void if the product has been damaged by accident or unreasonable use,
neglect, improper service or other causes not arising out of defects in materials or construction. 

ALL

WARRANTIES INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY,
WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE, AND WARRANTY OF
NON-INFRINGEMENT OF INTELLECTUAL PROPERTY ARE EXPRESSLY EXCLUDED TO THE
MAXIMUM EXTENT ALLOWED BY LAW, AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES
ANY PERSON TO ASSUME FOR IT ANY LIABILITY IN CONNECTION WITH THE SALE OF THE
PRODUCT. DIRECTED HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES
INCLUDING ITS AUTHORIZED DEALERS OR INSTALLERS.

Unit must be returned to Directed, postage

pre-paid, with: consumer's name, telephone number, and address, authorized dealer's name and address,
and product description. 

IN ORDER FOR THIS WARRANTY TO BE VALID, YOUR UNIT MUST BE

SHIPPED WITH PROOF OF INSTALLATION BY AN AUTHORIZED DIRECTED DEALER. ALL UNITS
RECEIVED BY DIRECTED FOR WARRANTY REPAIR WITHOUT PROOF OF DIRECTED DEALER
INSTALLATION WILL BE COVERED BY THE LIMITED 1 YEAR PARTS AND LABOR WARRANTY.

Note:

This warranty does not cover labor costs for the removal and reinstallation of the unit.

BY PURCHASING THIS PRODUCT, THE CONSUMER AGREES AND CONSENTS THAT ALL DISPUTES
BETWEEN THE CONSUMER AND DIRECTED SHALL BE RESOLVED IN ACCORDANCE WITH
CALIFORNIA LAWS IN SAN DIEGO COUNTY, CALIFORNIA.

22

Содержание PQ40.2

























Отзывы: