909 49290 Скачать руководство пользователя страница 34

Страница: 34 / 50

31cc Brushcutter / Line Trimmer

AFTER SALES SUPPORT

e-mail: [email protected]

1800 909 909

MODEL: №. BC35TS-2 • 49290

(toll free)

AFTER SALES SUPPORT

(toll free)

31cc Brushcutter / Line Trimmer

e-mail: [email protected]

1800 909 909

MODEL: №. BC35TS-2 • 49290

Feeding the line

The line trimmer has a bump feed mechanism which releases the line

without having to stop the engine.
1. To release additional line increase the speed of the motor to no less than

half speed, then, lightly tap the bump knob (34) on the ground while

operating the unit at high speed.

NOTE: Always keep the line fully extended for optimum cutting

performance. Line release becomes more difficult as the cutting line

becomes shorter. Cutting efficiency also decreases as the line

becomes shorter.

The line will not extend if the speed of the spool is not operating at least

half speed. If the line does not extend, increase the speed to full speed

while tapping the bump knob on the ground. If the line still does not

extend, stop the motor and check the line inside the spool has not tangled

and also ensure there is sufficient line in the spool.

2. Each time the head is bumped it releases approximately 2cm of line.

Release the line until it strikes the cut off knife (32). This may require

several taps.

NOTE: The cut off knife (32) on the clip-on line trimmer guard attachment

(33) will automatically cut off any excess line. For best results tap the head on

hard soil or bare ground. Never bump the spool head on concrete as it may

crack the spool housing. Make sure the cut off knife (32) protector has been

removed. It is recommended to replace the protector when the line trimmer

is not in use.

IMPORTANT. Do not hit stones (even small ones), piles of earth, and small

pieces of wood or anything else that could be hidden or poorly visible in

the grass. If you hit a large object by accident, or if you jam the cutting tool

due to overloading or having the cutter jammed with grass, you must stop

the engine.

NOTE: All protective devices of the machine as well as protective equip-

ment must be maintained in good operation condition during the period

of use.

NOTE: If the line is too short you may not be able to advance the line by

tapping it on the ground. If this is the case, stop the engine and manually

advance the line.

49290 909 BC/LT IM ED2.indd 32

8/02/2017 11:01 AM

Содержание 49290



















































Результаты поиска

Содержание 49290

Отзывы:

Похожие инструкции для 49290

Бренды по названию

Популярные бренды

909 49290, Руководство пользователя

Результаты поиска

Содержание 49290

Отзывы:

Похожие инструкции для 49290

Бренды по названию

Популярные бренды