909 49290 Скачать руководство пользователя страница 27

Страница: 27 / 50

31cc Brushcutter / Line Trimmer

AFTER SALES SUPPORT

e-mail: [email protected]

1800 909 909

MODEL: №. BC35TS-2 • 49290

(toll free)

AFTER SALES SUPPORT

(toll free)

31cc Brushcutter / Line Trimmer

e-mail: [email protected]

1800 909 909

MODEL: №. BC35TS-2 • 49290

IMPORTANT: Ensure the inner flange is mounted on the spindle of the line

trimmer. The outer flange (29), the protector (27), the 3T brushcutter blade

(28) and the blade nut (26) are NOT required when the line trimmer spool

& line assembly (35) is being fitted.
Keep these components in a safe place. The 3T

brushcutter blade (28) should be placed back in

the cardboard packaging/envelope.
2. Place the spool and line assembly (35) on the

spindle (20) and thread on to the spindle finger

tight in an anti clockwise direction all the way

down until the back of the spool makes contact

with the inner flange (30) (Fig AM),

3. Insert the long end of the supplied 4mm allen

key (37) through the spindle lock entry hole (19)

and into the hole on the inner flange (30).

(This locks the spindle allowing the spool and

line assembly (35) to be secured). Further tighten

the spool and line assembly (35) ensuring the

assembly is tight on the spindle (20) and inner

flange (30) before removing the 4mm allen key

from the spindle hole to release the spindle

being locked (Fig. AN).

Removing the Spool and Line Assembly

NOTE: Always ensure the engine is turned off before undertaking this assembly.
1. Lay the unit down so that the fuel tank bracket (39) is on the ground or

on a secure surface. Lift the gearbox end of the lower shaft (15) to gain

access to the output spindle (20).

2. Insert the long end of the supplied 4mm allen key (37) through the

spindle lock entry hole (19) and into the hole on the inner flange (30).

(This locks the spindle allowing the spool and line assembly to be

removed). (Fig. AN)

3. Loosen the spool and line assembly (35) in a clockwise direction until it

can be removed from the spindle (20). Remove the allen key (37) locking

the spindle (20) once the spool and line assembly (35) has been removed.

AN.

AM.

49290 909 BC/LT IM ED2.indd 25

8/02/2017 11:01 AM

Содержание 49290



















































Результаты поиска

Содержание 49290

Отзывы:

Похожие инструкции для 49290

Бренды по названию

Популярные бренды

909 49290, Руководство пользователя

Результаты поиска

Содержание 49290

Отзывы:

Похожие инструкции для 49290

Бренды по названию

Популярные бренды