background image

8  |  Demonstration Procedure 

 

 

Aprisa SR+ Demo Kit Guide 1.3.0 

 

4.

 

Demonstration Procedure 

All commands to be typed are shown in 

italics

 

Basic Operation 

 

1.

 

Open Internet Explorer and access 172.17.200.10 

a.

 

Username: 

admin

 

b.

 

Password: 

admin

 

2.

 

Show basic Web browser management 

a.

 

Tab through the various screens and explain about remote management 

3.

 

Show Test Button operation 

a.

 

Press  and  hold  the  Test Button  on  remote  radio  1  until the  LEDs flash.   Five  green  LEDs 
should appear indicating >-80 dBm RSSI 

b.

 

Disconnect  the  RF  cable  on  remote  radio  1  and  hold  it  close  to  the  RF  connector.    The 
LEDs should turn orange 

c.

 

Pull the cable away completely and the LEDs should turn red 

d.

 

Reconnect the cable.  The LEDs should turn back to all green 

e.

 

Press and hold the Test Button until the LEDs flash to exit the test mode 

4.

 

Open Terminal Emulator configured for RS-232 serial data and show transfer of a text file 

a.

 

Fit the RJ45 RS-232 loopback plug to remote radio 1 serial port 1 

b.

 

Send  a  text  file  from  the  base  station.  The  details  should  reappear  on  the  screen 
indicating that the file has been sent to that remote station, looped back at the  remote 
station RS-232 serial port and sent back to the base station 

c.

 

Remove  the  RS-232  loopback  connector  from  the  remote  radio  1  and  re-demonstrate 
showing the break in the loopback connection 

5.

 

Open cmd window and show Ethernet data transfer 

 note the flashing of Tx and Rx LEDs 

a.

 

ping 172.17.200.20 

b.

 

ping 172.17.200.30 

6.

 

Show data compression 

a.

 

In cmd window: 

ping 172.17.200.30 

l 1000

 

b.

 

Ping test should show transfer of 1000 bytes to be almost as fast as the 32 byte transfer 
from previous test 

7.

 

Show  Ethernet  and  RS-232  serial.    This  test  pings  Remote  Station  2  and  loops  back  serial  data 
through remote radio 1 

a.

 

Fit the RJ45 RS-232 loopback plug to remote radio 2 serial port 1 

b.

 

In cmd window: 

ping 172.17.200.20 

t

 

c.

 

With the Terminal Emulator, send serial data 

d.

 

In cmd window Ctrl C to stop the Ethernet test 

 

 

Содержание Aprisa SR+













Отзывы: