Instructions for use and installation
General description
Technical info
Uniko Lite Smart is a single pushbutton connected with a WiFi/
BLE module, with a single on-board relay operating in the 110-
230 V range up to a maximum of 7A; Uniko Lite is “Smart” and
can be controlled remotely via smartphone or App.
1. Push button with RGB LED backlite
2. Terminals I1 and I2 for optional button inputs
3. Neutral N terminal
4. L terminals for input phase
5. NC and NO terminals to connect output or normally open
or closed contacts
6. Load connection terminal C
7 x 2,5 mm
2
+5 °C
+45 °C
Operation voltage
110V – 230V /50-60Hz
Maxi electric current
7A
Max load
1610W
Technology
Radio WiFI/BLE
Exercise frequency
2.4 GHz
Standby consumption
1 Wh
For more info.
4box.it
Wiring diagrams
Uniko Lite Smart as a diverter.
Uniko Lite Smart use like an
inverter.
1
1
3
2
4
5
6
5
2
Operating mode
Uniko Lite Smart can be programmed to have functions of:
• Single light button
Confuguration
Precautions for use
All direct connections to the mains conductors must
be carried out by trained and authorized technical
staff. Pay attention to any danger indications placed
on the device or contained in this manual highlighted
with the symbol ( ).
Do not use the device in gas saturated environments.
Do not place the device near heat sources.
Use only indoors.
To perform the first installation, replacement and/or removal
of a device and for any other information, refer to the manual
which can be downloaded from the site.
Installation rules
Installation must be carried out by qualified staff
in compliance with the provisions governing the
installation of electrical equipment in force in the
country where the products are installed. The
installation must be carried out with the system
switched off.
Warranty
This product is covered by a 2 years from the date of purchase
on parts and labor warranty. To enforce the guarantee it
is necessary to keep the proof of purchase. The warranty
does not cover any damage due to shocks or accidents. The
components of the appliance must not be opened or repaired
by people outside 4box company.
Maintenance and cleaning
Disposal
Declaration of Conformity
Before cleaning, disconnect the product from the power
supply. The product does not require specific maintenance. To
clean the product, use a simple dry cloth. Do not use abrasive
or corrosive substances. Do not spray cleaning products
directly on the switch.
4 BOX declares under its own responsibility that the Uniko
Pro Smart device complies with the following directives and
that this conformity has been assessed in compliance with the
respective applicable standards:
• Directive 2014/53/EU (effective use of the radio spectrum in
order to avoid harmful interference).
• Reference standard: ETSI EN 300 328 V2.2.2
• Directive 2014/35/EU (protection of users’ health and
safety).
• Reference standard: EN 62368 -1:2014+A11:2017
• Directive 2014/30/EU (protection requirements regarding
electromagnetic compatibility).
• Reference standards: CEI EN 55032:2015, EN
55035:2017+A11:2020 and ETSI EN 301 489-1/17.
• Directive 2013/35 /EU (protection requirements regarding
physical agents).
• Reference standard: CEI EN IEC 62311:2021
• RoHS directive.
This logo indicates devices that are no longer
usable cannot be placed in the normal containers
for ordinary waste. The toxic substances that may
be contained in them, in fact, could represent a
risk to health and the environment. These devices
should be returned to your dealer or disposed of as
determined by local authorities.
EN
Uniko Lite Smart as an interrupted.
Diverter
Inverter
N
L
Diverter
Button or *
switch
N
L
*In the input it can be connected indiscriminately to Phase (L) or to Neutral (N)
