background image

15

After switching on the power supply, programming (pressing the buttons) must be 
carried out within 10 seconds. Otherwise the motor returns to its original state.

2 x Press button P2 / Set Up

of the already paired

 handheld transmitter

2 x Press button P2 / Set Up

1 x Press Down-button

 PROGRAMMING RADIO TRANSMITTER

Pairing handheld transmitters 
with Radio motor Type RNH:

The motor confirms 

the programming

with several 

beeps

OK

2 x Press button P2 / Set Up

1 x Press Up-button

Beep while

pressing

Long beep 

from motor

Switch on power supply.

Only switch the affected receiver 
to voltage.

Change direction of rotation 
of radio motor:

The motor confirms 

the programming

with several 

beeps

OK

Beep while

pressing

Long beep 

from motor

Switch on power supply.

Only switch the affected receiver 
to voltage.

Pairing another handheld 
transmitter:

The motor confirms 

the programming

with several 

beeps

OK

1 x Press button P2 / Set Up

of the new

 handheld transmitter

Beep while

pressing

Leave Power supply 
switched on.

Leave voltage of all motors 
switched on.

Important when teaching, changing or deleting transmitters:

Only one relevant motor may be switched to voltage!
Several radio motors or radio receivers can be programmed to form a group with the same transmission channel.
For multi-channel transmitters, channel by channel must be taught or transferred.

After switching on the power supply, programming (pressing the buttons) must be 
carried out within 10 seconds. Otherwise the receiver returns to its original state.

After switching on the power supply, programming (pressing the buttons) must be 
carried out within 10 seconds. Otherwise the motor returns to its original state.

3T-MOTORS Radio tubular motors

  |  Programming radio transmitter

Содержание 3T-MOTORS 3T45-20RNH





















Отзывы: