3MillID S-Gang Keypad Reader Скачать руководство пользователя страница 3

3millID   9249 S. Broadway   Building #200   Suite 826   Highlands Ranch   CO 80129

+1 303 475 4972

[email protected]

© 3millID

100-02640-A

www.3millid.com

1   x

reader MODULE

1   x

reader BACKPLATE

1   x

3 x 10mm black cross-head securing screw

10cm

up to

+

 -

66

35

C

5

yrs

1.

parts list

2.

specification

performance level for access control

This product complies with the following UL294 Access Control Performance Levels:
Destructive Attack

Level I

Line Security

Level I

Endurance

Level IV

Standby Power

Level I

See the UL Listed access control unit controller installation instructions for reader 
compatibility.

UL Ref. Number

??????

environmental

Operating Temperature

-35°C to +66°C 

(-31°F to + 151°F)

Humidity

85 ±5% at 30 ±2°C  

(86 ±3°F)

Ingress Protection

IP65 

(not evaluated by UL)

Positioning

Suitable for INDOOR and OUTDOOR use.

electrical

Power supply

Power is to be provided by a UL294 Listed, low-voltage
Class 2 power limited supply or control panel, capable
of 4 hours standby.

Voltage

+10Vdc to +16Vdc

Current

135mA typical

Data Voltage

Rest >4Vdc / Active <1Vdc

Data Output

Wiegand, Clock & Data, Custom Outputs

Indication

1 RGB LED + RGB illuminated keypad

Sounder

Integral speaker

dimensions

120mm x 76mm x 21mm (4.7 x 3.0 x 0.8 inches)

polymeric materials

Potting compound

UL R/C (QMFZ2)

Mouldings

UL746C

wiring

Wiring methods shall be in accordance with the
National Electrical Code (ANSI/NFPA70), local
codes, and the authorities having jurisdiction.

Recommended cable

BELDEN 953x (or equivalent UL listed) - Wiegand
BELDEN 9502 (or equivalent UL listed) - RS485
All cable and wiring must be Listed and suitable for use.

Cable length

Cable length must not exceed 30 metres maximum
(98.5 feet) for UL

Minimum permissible wire size

not less than 26 AWG (0.24mm²)

connections

Screw terminal

(All readers in this series use this terminal connection)

 1

-

0V

Supply voltage ground

 2

-

+Vdc

Supply voltage (+10Vdc to +16Vdc)

 3

-

DATA1/CLK

Wiegand or Clock/Data output

 4

-

DATA0/DAT

Wiegand or Clock/Data output

 5

-

GREEN

Green LED control input

 6

-

RED

Red LED control input

 7

-

Buzzer

Buzzer control input

 8

-

TMPR/CP

Tamper or Card Present output

 9

-

RS485-

RS485 Bus

10 -

RS485+

RS485 Bus

120mm

4.7 inches

21mm

0.8 inch

76mm

3.0 inches

6

8

0

9

#

4

7

*

5

1

2

3

MANUAL

3M

S-Gang

Keypad

3

Содержание S-Gang Keypad Reader













Отзывы: